Master Code Switch; Ring Pin Jumper; Relay 2 Jumper - DKS 1834 PC Programmable Installation & Owner's Manual

4.5 Master Code Switch

The master code switch MUST be kept in the OFF position for normal operation. Turn the master code
O N
switch ON only when programming the system's master code. See section 3.2.1 to program the system's
E R
S T
M A
master code. If the master code switch is turned ON and a new master code is NOT entered, the system will
D E
C O
sound a long tone after approximately 30 seconds. This tone will continue every 30 seconds until a new
F
O F
master code is entered, or until the switch is turned off.

4.6 Ring Pin Jumper

Always Answer Calls
The ring pin jumper is labeled RING on the control board. This jumper MUST be installed to allow the
system to ALWAYS answer the calls placed to it. If remote programming or remote relay operation is to be
used, the jumper MUST be installed on the pins. Removing the jumper will cause the system to NEVER
G
R I N
answer calls placed to it.
Never Answer Calls
G
R I N

4.7 Relay 2 Jumper

This jumper sets the contacts on relay number two at either Normally Open (NO) or Normally Closed (NC).
N C
The jumper is set to NO from the factory.
N O
4.8 Auto – 1816 Interface Jumper
This jumper sets the system to operate as a stand-alone unit - AUTO (top position), or to interface with the
Auto
1816 Telephone Intercom System (bottom position). The jumper is set to AUTO from the factory.
4.9 HF – HS Jumper
SURFACE Mount Handsfree
TELEPHONE ENTRY SYSTEM
SP SP ABC ABC DEF DEF
1 1 2 2 3 3
GHI GHI JKL JKL MNO MNO
4 4 5 5 6 6
PQRS PQRS TUV TUV WXYZ WXYZ
7 7 8 8 9 9
OPER OPER
0 0
HOLD TO SCAN
A
OPERATING INSTRUCTIONS
1. Use "A to Z" Buttons to Locate
Name and Code Number on Display.
Names are In Alphabetical Order.
Z
2. To Call, Enter Code Number on
Keypad or Press "Call" Button. If
Line is Busy, Press "#" or "Call" to
Hang Up. Try Again.
3. Enter on Open Display and Tone.
CALL
42
H F
H S
For Hands Free (HF)
operation, the jumper is
set in the left position.
SURFACE Mount Hand Set
For a system
with a Hand
Set (HS), the
TELEPHONE ENTRY SYSTEM
SP SP ABC ABC DEF DEF
1 1 2 2 3 3
jumper is set
GHI GHI JKL JKL MNO MNO
4 4 5 5 6 6
PQRS PQRS TUV TUV WXYZ WXYZ
7 7 8 8 9 9
OPER OPER
0 0
in the right
HOLD TO SCAN
A
OPERATING INSTRUCTIONS
1. Use "A to Z" Buttons to Locate
Name and Code Number on Display.
position.
Names are In Alphabetical Order.
Z
2. To Call, Enter Code Number on
Keypad or Press "Call" Button. If
Line is Busy, Press "#" or "Call" to
Hang Up. Try Again.
3. Enter on Open Display and Tone.
CALL
FLUSH Mount Hand Set
TELEPHONE ENTRY SYSTEM
SP SP ABC ABC DEF DEF
1 1 2 2 3 3
GHI GHI JKL JKL MNO MNO
4 4 5 5 6 6
PQRS PQRS TUV TUV WXYZ WXYZ
7 7 8 8 9 9
OPER OPER
0 0
HOLD TO SCAN
OPERATING INSTRUCTIONS
1. Use "A to Z" Buttons to Locate
Name and Code Number on Display.
Names are In Alphabetical Order.
2. To Call, Enter Code Number on
Keypad or Press "Call" Button. If
Line is Busy, Press "#" or "Call" to
Hang Up. Try Again.
H F
3. Enter on Open Display and Tone.
H S
A
Z
CALL
1834-065-B-10-14