Roland VersaCamm SP-540V Service Notes page 110

Service Report
Roland Versa CAMM
Model
Version
Serial No.
Ink type
Edge detection
Empty mode
Calibration
Media clamp
Full width scanning
Sheet remain
Sheet remain at loading : ENABLE
Bi-dir. adjust No.1
No.2
No.3
No.4
Tool Parameter
Force
Velocity
Offset
Up Velocity
Service Report
Head rank H1
H2
Dip SW
System SW page1-4 : 01000000 00000000 01100001 00000000
page5-8 : 00000000 00000100 00000000 00000000
page9-12 : 00000000 00000100 00000000 00000000
Head hori.(DT1.Low)
(DT3.Low)
(DT1.High)
(DT3.High)
Head bi. (DT1.Low)
(DT3.Low)
(DT1.High)
(DT3.High)
Limit position
Cutter Down Position
Calibration default
Encorder position (L)
Encorder position (R)
Environment match
Encoder calibration
: SP-540V
: 4.00
: XX00002
: ECO-SOL 4Color
: ENABLE
: Stop
: 0.00%
: SHORT
: DISABLE
: 28.5m
: H1 H2
: 0 0
: 0 0
: -2 -2
: -2 -2
: 105 gf
: 25 cm/s
: 0.250 mm
: 30cm/s
: 7CV3738UTVYWXSU
: 7FU3939RUSYXWSV . . . . . . . . . . . .
: 00100000
: H1 H2
: +6
: +7
: +7
: +8
: +18 +19
: +16 +17
: +26 +27
: +24 +25
: 20.8 mm
: 1828.2 mm
: 0.00 %
: 1575.0 mm
: 203.4 mm
: +0.181%
: +0.181%
4-13
Ink remain(1-4)
Head Temperature
Heater temp.(Print)
Heater temp.(Dryer)
Length unit
Temperature unit
Menu language
Sleep
Sleep interval
Head height
Scan interval
Vacuum power
Heater setting(Print)
Heater setting(Dryer)
Preheating
Feed for Dry
Cutting calib. (F/S)
Print-cut adjust (F/S)
Cutting priority
Prefeed
. . . . . . . . . . . . 40W. . D
30E. . D
Maintenance request
Booter version
Battery
Cap adjust
Heater adjust (Print)
Heater adjust (Dryer)
Preheat temperature
Heating timeout
Force adjust 30gf
Force adjust 200gf
Crop-tool adjust (F/S)
Print-cut adjust (F/S)
Pinch Adjust
Crop sensor adjust
Timeout
: 99/95/93/94
: 29 C / 84.2 F
: 37 C / 98 F
: 41 C / 104 F
:mm
: C
: English
: ENABLE
: 30 min
: HIGH
: 0.0 sec.
: AUTO
: 37 C / 98 F
: 40 C / 104 F
: MENU
: DISABLE
:0.00/ 0.00%
:0.00/ 0.00mm
: COMMAND
: DISABLE
: NONE
: 1.03
: Charged
: 0.00 mm
: 0 C
: 0 C
: 35 C
: 20 min
: 10
: 51
: - 0.50/ -0.20 mm
: +0.11/ -0.60 mm
: 1.55 mm
: 0
: NONE
4