ADEMCO Vista-20HW Installation Instructions Manual page 62

The following describes each format in greater detail.
3+1 and 4+1 Standard Formats
3+1 and 4+1 Expanded Formats
4+2 Format
Ademco Contact ID
Reporting Format
Where:
SSS or Ssss =
A=
z=
Tt =
Bb =
EAC .
LLB =
0=
Comprise a 3- (or 4-) digit subscriber number and a single digit
report code (e.g. Alarm, Trouble, Restore, Open, Close, etc).
Comprise a 3- (or 4-) digit subscriber number, and a two-digit re-
port code. The first digit is displayed on the first line, followed
by
a
second line where the first digit is repeated 3 (or 4)
times
and followed by the second digit. This is the "expanded" digit.
Comprises
a
4-digit
subscriber number and 2-digit report code.
Comprises a 4-digit subscriber number, l-digit event qualifier
("new" or "restore"), 3-digit event code, 2-digit Partition No., and
3-digit zone number, user number, or system status number (see
the following page).
3+114+1 3+1/4+1
Report
Standard Expanded
4+2
Alarm SSS(S)
A SSS(S)A
Ssss M
AAA(A) Z
Trouble
SSS(S)T
SSS(S)T
Ssss Tt
TM'(T) t
Bypass SSS(S)B SSS(S) B SSSSBb
BBB(B)b
AC
LOSS
SSS(S)
E SSS(S)E SSSSE&
EEE(E)Ac
Low Batt
SSS(S)L
SSS(S) L SSSSLLB
LLL(L)LB
Open
Sss(s) o
Sss(s) o Ssss Ou
000(0) u
b
Close Sss(s) c Sss(s) c Ssss Cu
ccc(c) u
Test SSS(S) G SSS(S) G SSSS Gg
GGG(G)g
Restore
SSS(S)R
SSS(S) R
Ssss FtZ
Alarm
RRR(R)Z
AC Restore SSS(S)RA SSS(S)RA SSSSRA~
RARARA(RA)&
LoBatRes.
SSS(S)RL
SSS(S) RL SSSSRLLB
RLRLRL(RL)LB
TroubleRes. SSS(S)RII SSS(S)RT SSSSRqt
RTRTRT7q)t
BypassRes.
SSS(S)RB
SSS(S) RB SSSSRBb
RBRBRB(~)b
Subscriber ID
Alarm Code-1 st digit
Typically Zone Number"–2nd digit
Trouble Code (1st & 2nd digits)
Bypass Code (1st & 2nd digits)
AC Loss Code (lst & 2nd digits)
Low Battery Code(l et & 2nd digits)
Open Code-lst Digit
'Zone numbers foc
C = Close Code-1st Digit
U = User Number
(in hex)
Gg = Test Code (Ist & 2nd digits)
R = Restore Cede (Alarm)
R Tt = Restore Code (Trbl)l St & 2nd digits
RBb=
Restore Code (Byps)l st & 2nd digits
RAAC =
Restore Code (AC)l st & 2nd digits
RLLB = Restore Code (Bat)lst & 2nd digits
[x] & [#], or [B] =99 [1]+ [x], or [A] =95
Duress = 92
[3] + [#], or [C] =96
Tamper = 9
-62-