Panasonic AJ-SPX900e Operating Instructions Manual page 50

Information Item
Camera Warning and
Report Area
(related to AWB, ABB
and switch settings)
(Switch changeover
indication)
(Low light warning)
(CALL indication)
(Y GET value)
(MARKER indication)
User button
functions
UM: USER MAIN
button
U1: USER1 button
U2: USER2 button
Filter positions
WHITE BAL switch
position
50
Indication
AWB A ACTIVE
AWB B ACTIVE
AWB A OK . K
AWB B OK . K
AWB BREAK . K
AWB NG
COLOR TEMP LOW
COLOR TEMP HIGH
LEVEL OVER
LOW LIGHT
TIME OVER
AWB PRESET . K
ATW MODE
CHECK FILTER
AWB A VAR . K
AWB B VAR . K
ABB ACTIVE
ABB OK
ABB BREAK
ABB NG
W-SHD ACTIVE
W-SHD OK
W-SHD BREAK
W-SHD NG
LVL OVER
B-SHD READY
B-SHD ACTIVE
B-SHD OK
B-SHD BREAK
B-SHD NG
WHITE: # . K
AUTO KNEE: ON/OFF
GAIN: dB
SS: 1/
SS: 1/
SS: SUPER V
CC: K
ND:
EXTENDER: ON/OFF
IRIS: F .
LOW LIGHT
CALL
. %
MKR: A/B/OFF
INH
S.GAIN dB/OFF
DS.GAIN /OFF
S.IRIS ON/OFF
I.OVR ON/OFF
S.BLK – /OFF
B.STR ON/OFF
AUDIO CH1
AUDIO CH2
REC SW
Y GET ON
RET SW
ATW ON/OFF
D.ZOOM ON/OFF
NEWS-G ON/OFF
SLOT SEL
1 - 4
A - D
-
A
B
P
T
AWB being performed on Ch A.
AWB being performed on Ch B.
AWB successful on Ch A.
AWB successful on Ch B.
AWB action aborted by user.
AWB action failed. The second line indicates the status.
Color temperature too low.
Color temperature too high.
Brightness too high.
Brightness too low.
Action timed-out.
AWB cannot proceed because the AWB switch is positioned at [PRE].
AWB cannot proceed during ATW.
Make sure the FILTER control is positioned correctly.
AWB cannot proceed because [A] is set to "VAR".
AWB cannot proceed because [B] is set to "VAR".
ABB being performed.
ABB action successful.
ABB action aborted by user.
ABB action failed.
White shading being adjusted.
White shading has been adjusted.
White shading action aborted by user.
White shading adjustment failed due to excessive brightness.
Black shading accepted (by holding down the ABB switch during ABB adjustment).
Black shading being adjusted.
Black shading adjustment successful.
Black shading adjustment aborted by user.
Black shading adjustment failed.
The WHITE BAL switch has been switched. # is replaced with A, B or PRE. When
[A] and [B] are set to "VAR", then it is indicated as VAR
assigned ATW, then it is indicated as ATW MODE.
AUTO KNEE switch has been switched to ON or OFF.
Gain has been switched with the GAIN selector switch or a user button.
When the shutter speed has been switched, the shutter speed is indicated.
Shutter speed is in SYNCRO SCAN mode.
Shutter speed is in SUPER V mode.
Indicated when the CC filters are switched.
Indicated when the ND filters are switched.
Lens extender has been turned on or off.
Indicated when the iris override correction value is to be changed.
Brightness too low.
Displayed when CALL command is issued from the extender.
When the Y GET function is being carried out (the output brightness level near the
center marker is being measured for about three seconds: the level is represented
as a percentage), the output brightness level near the center marker is indicated as
a percentage.
Current marker type
User buttons disabled.
Selected S.GAIN
Selected DS.GAIN
Whether S.IRIS is ON or OFF.
Iris override can be set (the IRIS OVERRIDE setting is ON).
Status of SUPER BLACK (ON or OFF). When it is ON, the set value is also
indicated.
Status of BLACK STRETCH (shade correction for the black level): ON or OFF
Input signal to be recorded on Audio Channel 1 has been switched.
Input signal to be recorded on Audio Channel 2 has been switched.
USER button acts as REC switch.
Y GET function ON.
USER button acts as RET switch.
ATW being performed.
Status of the digital zoom (ON or OFF)
Status of News Gamma (ON or OFF)
Switch that changes the target card is set.
Position of the ND filter.
Position of the CC filter.
Filter not positioned correctly.
WHITE BAL switch positioned at [A].
WHITE BAL switch positioned at [B].
WHITE BAL switch positioned at [PRE].
ATW mode active. When brightness and color are outside operating limits, the
indication blinks.
Status
. K. When [B] is