Parameter List - Mitsubishi Electric FR-D700 Instruction Manual

Parameter list

4.2 Parameter list
4.2.1 Parameter list
For simple variable-speed operation of the inverter, the initial setting of the parameters may be used as they are. Set the
necessary parameters to meet the load and operational specifications. Parameter setting, change and check can be made
from the operation panel. For details of parameters, refer to the instruction manual.
REMARKS
indicates simple mode parameters.
The parameters surrounded by a black border in the table allow its setting to be changed during operation even if "0" (initial
value) is set in Pr. 77 Parameter write selection.
Func-
Parameter Name
tion
0 Torque boost
1 Maximum frequency
2 Minimum frequency
3 Base frequency
4 Multi-speed setting (high speed)
5 Multi-speed setting (middle speed)
6 Multi-speed setting (low speed)
7 Acceleration time
8 Deceleration time
9 Electronic thermal O/L relay
10 DC injection brake operation frequency 0 to 120Hz
11 DC injection brake operation time
12 DC injection brake operation voltage
— 13 Starting frequency
— 14 Load pattern selection
15 Jog frequency
16 Jog acceleration/deceleration time
— 17 MRS input selection
— 18 High speed maximum frequency
— 19 Base frequency voltage
Acceleration/deceleration reference
20
frequency
22 Stall prevention operation level
Stall prevention operation level
23
compensation factor at double speed
24 Multi-speed setting (speed 4)
25 Multi-speed setting (speed 5)
26 Multi-speed setting (speed 6)
27 Multi-speed setting (speed 7)
Acceleration/deceleration pattern
— 29
selection
52
Minimum Refer
Initial
Setting Range Setting to
Value
Increments Page
0 to 30% 0.1% 6/4/3% 69
∗1
0 to 120Hz 0.01Hz 120Hz 78
0 to 120Hz 0.01Hz 0Hz 78
0 to 400Hz 0.01Hz 50Hz 80
0 to 400Hz 0.01Hz 50Hz 84
0 to 400Hz 0.01Hz 30Hz 84
0 to 400Hz 0.01Hz 10Hz 84
0 to 3600s 0.1s 5/10s 91
∗2
0 to 3600s 0.1s 5/10s ∗2 91
Rated
0 to 500A 0.01A inverter 95
current
0.01Hz 3Hz
104
0 to 10s 0.1s 0.5s 104
0 to 30% 0.1% 6/4% 104
∗3
0 to 60Hz 0.01Hz 0.5Hz 93
0 to 3 1 0 82
0 to 400Hz 0.01Hz 5Hz 86
0 to 3600s 0.1s 0.5s 86
0, 2, 4 1 0 110
120 to 400Hz 0.01Hz 120Hz 78
0 to 1000V, 8888, 9999 0.1V 8888 80
1 to 400Hz 0.01Hz 50Hz 91
0 to 200% 0.1% 150%
74
0 to 200%, 9999 0.1% 9999 74
0 to 400Hz, 9999 0.01Hz 9999 84
0 to 400Hz, 9999 0.01Hz 9999
84
0 to 400Hz, 9999 0.01Hz 9999 84
0 to 400Hz, 9999 0.01Hz 9999 84
0, 1, 2 1 0 94
These instruction codes are used for parameter read and write by using Mitsubishi inverter protocol with the RS-485 communication.
(Refer to page 204 for RS-485 communication)
" " indicates valid and "×" indicates invalid of "control mode-based correspondence table", "parameter copy", "parameter clear", and "all parameter clear".
Customer
Parameter Remarks
Setting
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
29
Control Mode-based
Instruction Code
Correspondence Table
Read Write Extended Copy
V/F V/F V/F GP MFVC GP MFVC GP MFVC
×
00 80 0
01 81 0
02 82 0
×
03 83 0
04 84 0
05 85 0
06 86 0
07 87 0
08 88 0
09 89 0
0A 8A 0
0B 8B 0
0C 8C 0
0D 8D 0
×
0E 8E 0
0F 8F 0
10 90 0
11 91 0
12 92 0
×
13 93 0
14 94 0
16 96 0
17 97 0
18 98 0
19 99 0
1A 9A 0
1B 9B 0
1D 9D 0
Parameter list
Parameter
Clear All clear
4