Saftronics FP5 Series User Manual page 46

efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor
Chapter 3 - Programming Features
FP5/GP5 Parameters
No. Function Name
(LCD Operator Display)
n065 Elapsed timer selection
(Elapsed Timer)
n066 Elapsed timer 1
(Elapsed Time 1)
n067 Elapsed timer 2
(Elapsed Time 2)
n068 DC injection current
(DCInj Current)
n069 DC injection time at stop
(DCInj Time @ Stop)
n070 DC injection time at start
(DCInj Time @ Start)
n071 Torque compensation
gain
(Torq Comp Gain)
n072 Stall prevention during
deceleration
(StallP Decel Sel)
n073 Current limit/Stall preven-
tion level during accelera-
tion
(StallP Accel Lvl)
n074 Current limit/Stall preven-
tion level during running
(StallP Run Level)
n075 Frequency agree set point
(Freq Det Level)
n076 Frequency agree
detection width
(Freq Det Width)
n077 Over/Undertorque
detection OL3
(Torq Det Sel)
46
Description
LED
Setting LCD Setting Description
0 Time Power is ON Accumulate time during power on
1 Time Running Mtr Accumulate time during running
Unit: 1 hour Range: 0~9999
* Initial value becomes 0 only when initialized dur-
ing CPF4 occurrence.
Unit: 10,000 hours Range: 0~27
* Initial value becomes 0 only when initialized dur-
ing CPF4 occurrence.
Unit: 1%
Setting range: 0~100%
100% = inverter rated current
Unit: 0.1s
Setting range: 0.0~10.0s
Unit: 0.1s
Setting range: 0.0~10.0s
Unit: 0.1
Setting range: 0.0~3.0
(normally, no adjustment is necessary)
LED
Setting LCD Setting
0 Disabled
1 Enabled
Unit: 1% Setting range: 30~200%
When level is set to 200%, current limit during
acceleration is disabled.
Unit: 1% Setting range: 30~200%
When level is set to 200%, current limit during
running is disabled.
Unit: 0.1Hz
Setting range: 0.0~400.0Hz
Unit: 0.1Hz
Setting range: 0.0~25.5Hz
LED
Setting LCD Setting Description
0 Disabled Detection disabled
1 OT/Spd Agree/Alm Overtorque detection at speed agree;
continue running after detection.
(Alarm)
2 OT/Run/Alm Overtorque detection at run; continue
running after detection. (Alarm)
3 OT/Spd Agree/Flt Overtorque detection at speed agree;
coast to stop after detection. (Fault)
4 OT/Run/Flt Overtorque detection at run; coasts to
stop after detection. (Fault)
5 UT/Spd Agree/Alm Undertorque detection at speed
agree; continue running after detec-
tion. (Alarm)
6 UT/Run/Alm Undertorque detection at run; con-
tinue running after detection. (Alarm)
7 UT/Spd Agree/Flt Undertorque detection at speed
agree; coast to stop after detection.
(Fault)
8 UT/Run/Flt Undertorque detection at run; coast to
stop after detection. (Fault)
FP5/GP5 User's Manual
Factory User Ref.
Default Setting Page
Time -
Running
Mtr
* -
* -
50% 54,75
0.0s 54
0.0s 55,75
1.0 72
Enabled 54
kVA 52
dependent
kVA 53
dependent
0.0Hz 57,84
2.0Hz 84
73
Disabled