Saftronics FP5 Series User Manual page 44

efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor
Chapter 3 - Programming Features
FP5/GP5 Parameters
No. Function Name
(LCD Operator Display)
n037 Multi-function input 2
(Terminal S3 Sel)
n038 Multi-function input 3
(Terminal S4 Sel)
n039 Multi-function input 4
(Terminal S5 Sel)
n040 Multi-function input 5
(Terminal S6 Sel)
n041 Multi-function output
selection 1
(Terminal MA Sel)
n042 Multi-function output
selection 2
(Terminal M1 Sel)
n043 Master analog input selec-
tion - FV or FI terminal
(Analog Input Sel)
n044 Aux. analog input
selection
(Terminal FI Sel)
n045 Frequency reference
retention
(MOP Ref Memory)
n046 Operation method for
frequency reference
loss detection
(Ref Loss Detect)
44
Description
Set items are same as n036.
(When n036="FWD/REV Cmd (3W), "In Use By
Other" is displayed, and setting is prohibited)
Set items are same as n036.
Set items are same as n036.
(When n040="Up/Down Control", "In Use By Other
is displayed, and setting is prohibited)
Set items are same as n036.
LED
Setting LCD Setting Description
29 Up / Down control Up / Down command (Terminal
S5=Up command, and terminal
S6=Down command).
LED
Setting LCD Setting Description
0 Fault Fault
1 During Running During running
2 At Speed Frequency agree
3 At Desired Speed Desired frequency agree
4 Freq Detection 1 Frequency detection 1
5 Freq detection 2 Frequency detection 2
6 OverTrq Det (NO) Over/Undertorque detection (nor-
mally open)
7 OverTrq Det (NC) Over/Undertorque detection (nor-
mally closed)
8 Baseblocked During baseblock
9 Operation Mode Local mode
10 Ready Inverter operation ready
11 Timer Output Timer function
12 Auto-Restarting During auto restart
13 OL Pre-Alarm OL pre-alarm (80% OL1 or OL2)
14 Freq Ref Loss Frequency reference loss
15 Set By COM Cntl Closed by serial communication
16 PID Fdbk Loss PID feedback loss
17 OH1 Alarm OH1 Alarm (set if n035 set to "3")
Set items are as same as n041
LED LCD
Setting Setting FV FI
0 FV=MSTR FI=AUX Master Aux.
1 FV=AUX FI=MSTR Aux. Master
2 FV=RST FI=MSTR Fault reset Master
Enable: FV/FI switchover function is enabled.
Disable: FV/FI switchover function is disabled.
Note: When PID is enabled (n084 ≠ 0),
FV terminal = PID reference, and
FI terminal = PID feedback.
LED
Setting LCD Setting Description
0 0-10VDC 0~10V input (Jumper J1 must be cut)
1 4-20mA 4~20mA input
LED
Setting LCD Setting Description
0 Memorize Fref Retained in frequency reference 1 (n024)
1 Not Memorized Not retained after power-down
LED
Setting LCD Setting Description
0 Not detected No detection
1 Run @ n047 Fref Continue to run at n047 setting
FP5/GP5 User's Manual
Factory User Ref.
Default Setting Page
Ext 78
Fault
(NO)
Fault 78
Reset
Multi- 78
Step
Spd 1
Multi- 78
Step
Spd 2
Fault 83
During 83
Running
FV=MSTR 82
Remarks
FI=AUX
Enable
Enable
Disable
4-20mA 82
Memorize 82
Fref
Not 82
Detected