Toshiba TOSVERT VF-AS1 Instruction Manual page 14

6.24 Torque control
6.24.1 Torque command
6.24.2 Speed limits in torque control mode
6.24.3 Torque bias and load sharing gain
6.25 Torque limit
6.25.1 Torque limit switching
6.25.2 Torque limit mode selection at acceleration/deceleration
6.26 Stall prevention function
6.26.1 Power running stall continuous trip detection time
6.26.2 Regenerative braking stall prevention mode selection
6.27 Current and speed control gain
6.28 Fine adjustment of frequency setting signal
6.29 Operating a synchronous motor
6.30 Acceleration/deceleration 2
6.30.1 Setting acceleration/deceleration patterns and switching acceleration/deceleration
patterns 1, 2, 3 and 4
6.31 Pattern operation
6.32 Preset speed mode
6.33 Protection functions
6.33.1 Setting of stall prevention level
6.33.2 Inverter trip record retention
6.33.3 Emergency stop
6.33.4 Output phase failure detection
6.33.5 OL reduction starting frequency
6.33.6 Motor 150%-overload time limit
6.33.7 Input phase failure detections
6.33.8 Control mode for low current
6.33.9 Detection of output short circuit
6.33.10 Overtorque trip
6.33.11 Cooling fan control selection
6.33.12 Cumulative operation time alarm setting
6.33.13 Abnormal speed detection
6.33.14 Overvoltage limit operation
6.33.15 Undervoltage trip
6.33.16 Regenerative power ride-through control level
6.33.17 Braking answer waiting time
6.33.18 VI/II analog input wire breakage detection level
6.33.19 Guide to time of replacement
6.33.20 Rush current suppression relay activation time
6.33.21 Motor thermal protection
6.33.22 Braking resistance overload curve
6.33.23 Selection of a restart condition for the motor stopped with a mechanical brake
6.33.24 Protection against a failure of the control power backup device (optional CPS002Z)
6.34 Override
6.35 Adjustment parameters
6.35.1 Pulse train output for meters
6.35.2 Setting of optional meter outputs
6.35.3 Calibration of analog outputs
6.36 Operation panel parameter
6.36.1 Prohibition of key operations and parameter settings
6.36.2 Displaying the rotational speed of the motor or the line speed
6.36.3 Changing the steps in which the value displayed changes
6.36.4 Changing the standard monitor display
6.36.5 Canceling the operation command
6.36.6 Selection of operation panel stop pattern
6.36.7 Setting of a torque command in panel operation mode
6.36.8 Torque-related parameters for panel operation
6.37 Tracing functions
iii
E6581445
F-43
F-43
F-43
F-43
F-45
F-45
F-47
F-49
F-49
F-49
F-49
F-50
F-50
F-51
F-51
F-54
F-56
F-57
F-57
F-57
F-58
F-59
F-59
F-59
F-59
F-60
F-61
F-61
F-62
F-62
F-63
F-63
F-63
F-64
F-64
F-64
F-65
F-65
F-65
F-65
F-66
F-66
F-68
F-70
F-70
F-71
F-71
F-72
F-72
F-73
F-74
F-75
F-75
F-75
F-75
F-76
F-76