Toshiba TOSVERT VF-AS1 Instruction Manual page 274

[27] Operation panel parameters [1/3]
Communi
Title cation Function
No.
Parameter write protect
0700

selection
0701 Current/voltage unit selection

Frequency free unit display
0702

magnification
Frequency free unit conversion
 0703
selection
Free unit display gradient
 0705
characteristic
 0706 Free unit display bias
 0707 Changing step selection 1
 0708 Changing step selection 2
 0709 Standard monitor hold function
Standard monitor display
0710

selection
Status monitor 1 display
0711

selection
Status monitor 2 display
 0712
selection
Status monitor 3 display
 0713
selection
Status monitor 4 display
 0714
selection
Status monitor 5 display
0715

selection
Status monitor 6 display
 0716
selection
Status monitor 7 display
 0717
selection
Status monitor 8 display
 0718
selection
Operation command clear
0719 selection when standby terminal

(ST) is OFF
Operation panel stop pattern
 0721
selection
Operation panel torque
 0725
command
Operation panel tension torque
0727

bias
Operation panel load sharing
0728

gain
Operation panel override
 0729
multiplication gain
Operation panel frequency
 0730
setting prohibition selection
This parameter moves to a fundamental parameter. *1: ⇒ For the adjustment range, see the table on page K-39.
Adjustment range
0:Permit
1:Prohibit
0:%, 1:A (ampere)/V (volt)
0.00:OFF, 0.01~200.0
0:All frequencies display free unit conversion
1:PID frequencies free unit conversion
0:Negative inclination (downward slope)
1:Positive inclination (upward slope)
0.00~ Hz
0.00:Disabled, 0.01~ Hz
0:Disabled, 1~255
0:Real time, 1:Peak hold, 2:Minimum hold
0~70 *1
Ditto
Ditto
Ditto
Ditto
Ditto
Ditto
Ditto
Ditto
0:Clear operation command
1:Retain operation command
0:Deceleration stop
1:Coast stop
-250~250%
-250~250%
0~250%
-100~100%
0:Permit
1:Prohibit
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
setting unit Default Write during
Speed
(Panel/Communi setting running
control
cation)
1/1 0 Enabled ●/●
1/1 0 Enabled ●/●
0.01/0.01 0.00 Enabled ●/●
1/1 0 Enabled ●/●
1/1 Enabled ●/●
0.01/0.01 0.00 Enabled ●/●
0.01/0.01 0.00 Enabled ●/●
1/1 0 Enabled ●/●
1/1 0 Enabled ●/●
1/1 0 Enabled ●/●
1/1 1 Enabled ●/●
1/1 2 Enabled ●/●
1/1 3 Enabled ●/●
1/1 4 Enabled ●/●
1/1 8 Enabled ●/●
1/1 16 Enabled ●/●
1/1 15 Enabled ●/●
1/1 14 Enabled ●/●
1/1 1 Enabled ●/●
1/1 0 Enabled ●/●
1/0.01 0 Enabled -
1/0.01 0 Enabled -
1/0.01 100 Enabled -
1/0.01 0 Enabled ●/●
1/1 0 Enabled ●/●
PM
Torque V/f Constant Reference
control
control
●/● ● ● 6. 36. 1
●/● ● ● 5. 15
●/● ● ● 6. 36. 2
●/● ● ● 6. 36. 2
●/● ● ● 6. 36. 2
●/● ● ● 6. 36. 2
●/● ● ● 6. 36. 3
●/● ● ● 6. 36. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 8. 3
●/● ● ● 6. 36. 5
●/● ● ● 6. 36. 6
●/● - - 6. 36. 7
●/● - - 6. 36. 8
●/● - - 6. 36. 8
- ● ● 6. 34
●/● ● ● 6. 36. 1