Fujitsu ETERNUS DX80 S2 User Manual page 175

Appendix B Audit Log List
Event code
020C0004
020C0005
020C0006
020C0007
020C0008
ETERNUS DX80 S2/DX90 S2 Disk storage system User's Guide -Operation-
Upper: Message
Lower: Detailed information
Set Box ID
$a
[ID= ]
Set Power Synchronization
[Connect=$a Auto=$b Resume=$c Timer=#d
Power_Fail=$e Low_Battery=$f
UPS_Shutdown_Signal=$g UPS_Shutdown=$h]
Set SED Authentication
Detail information is not displayed.
Set SMI-S
$a
[Function= ]
Set Subsystem Parameter
$a
[Load_Balance= 1cm_Write_Through=
High_Altitude= $c Read_Sequential=
$e
Write_Sequential= Reject_Inquiry=
$g
Critical_Disk_Mode=
$h
Disk_Media_Error_Check=
$i
Rd_Compare_Online_Count=
$j
Rd_Compare_Nrline_Count= All_LBAs=
$l
TPP_Alloc_Mode= Chk_BID_After_Write=
Reduce_Timeout_Nrline= $n Cache_Mirroring=
$p
Skip_Retry_Access_Disks=
Checkcode_Enforce_Mode= $q
$r
Disk_Fail_Early_Detect=
$s
Use_Add_Host_Group= Use_Add_Host=
Copyright 2013 FUJITSU LIMITED
The Box ID is set.
$a : Box ID
The power synchronization settings are changed.
$a : Controller module that is managed with
the power synchronization function (None,
CM0, CM1)
$b
: Auto Power function (Enable, Disable)
$c
: Power Resume function (Enable, Disable)
$d
: Delay until shutdown [sec]
$e
: Power failure signal logic (Positive,
Negative)
$f
: Low battery signal logic (Positive,
Negative)
$g
: UPS shutdown signal logic (Positive,
Negative)
$h
: UPS shutdown signal (Enable, Disable)
The SED authentication key is registered.
The SMI-S function is enabled or disabled.
$a
: SMI-S function (Enable, Disable)
The subsystem parameters are set.
$a : Load Balance (Enable, Disable)
$b
$b
: 1CM Write Through (Enable, Disable)
$d
$c
: Highland Mode (Enable, Disable)
$f
$d
: Read Sequential (Enable, Disable)
$e
: Write Sequential (Enable, Disable)
$f
: Reject INQUIRY from Unauthorized Host
(Enable, Disable)
$k
$g : Critical Disk Mode (Enable, Disable)
$m
$h
: Disk Media Error Check (Mode1, Mode2)
$o
$i : Read Compare Mode for Online Disks (0 –
255)
$j
: Read Compare Mode for Nearline Disks (0 –
255)
$t
]
$k
: All LBAs (Enable, Disable)
$l : Thin Provisioning Allocation Mode (TPP
Balancing, TPV Balancing)
$m : Check BID after Write Command (Enable,
Disable)
$n
: Reduce the Timeout Period for Nearline
Disks (Enable, Disable)
$o
: Cache Mirroring (Enable, Disable)
$p
: Skip Retry when Failed to Access Disks
(Enable, Disable)
$q : Check the checkcodes of all the data
blocks (Enable, Disable)
$r : Early detection-and-isolation of a failed
disk (Enable, Disable)
$s
: Use "Add Host Group" (Enable, Disable)
$t
: Use "Add Host" (Enable, Disable)
175
Description
P3AM-4842-12ENZ0