Download Print this page

Advertisement

P3AM-5332-15ENZ0
FUJITSU Storage
ETERNUS DX
Configuration Guide -Server Connection-
(Fibre Channel) ETERNUS DX80 S2/DX90 S2,
ETERNUS DX410 S2/DX440 S2,
ETERNUS DX8100 S2/DX8700 S2 Disk Storage System Settings

Advertisement

   Related Manuals for FUJITSU ETERNUS DX80 S2

   Summary of Contents for FUJITSU ETERNUS DX80 S2

  • Page 1

    P3AM-5332-15ENZ0 FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX80 S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage System Settings...

  • Page 2

    This page is intentionally left blank.

  • Page 3

    ETERNUS DX, server, OS, Fibre Channel cards, and drivers. Refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Notations" for the notations used in this manual such as product trademarks and product names. For storage systems that are supported by the OS, refer to the Server Support Matrix of the ETERNUS DX.

  • Page 4: Table Of Contents

    2.1.7 Allocating LUN Groups (Setting the Host Affinity)....................12 2.2 Specific Settings ........................... 12 2.2.1 Setting the CA Reset Groups..........................12 2.2.2 Setting the Subsystem Parameters ........................12 2.3 Checking the WWNs ........................13 FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-5332-15ENZ0...

  • Page 5

    Transfer Rate setting values (for Fabric connection) ..................9 Table 2.5 Host response settings ..........................10 Table 2.6 Host response settings for the ETERNUS DX8000 S2 series when using the TPG Referrals function ..11 FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-5332-15ENZ0...

  • Page 6: Chapter 1 Workflow

    Chapter 1 Workflow This manual is used when performing the setup procedures described in the "Setting Up the ETERNUS DX" section of the "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)" for each OS. Required Documents "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) Fibre Channel •...

  • Page 7

    "2.3 Checking the WWNs" (page 13) • After completing all the required procedures in this manual, follow the procedures in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)" for each OS. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-...

  • Page 8: Chapter 2 Setting Up The Eternus Dx

    Values from 0x10 upwards 0x00 (Except 0x7D) Transfer Rate See the table below (*1) FC Frame Size 2048 Reset Scope I_T_L Release Reservation if Chip is Reset Disable FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-5332-15ENZ0...

  • Page 9: Table 2.2 Transfer Rate Setting Values (for Fc-al Connection)

    When using a Fabric connection, complete the preparatory work and set up the Fibre Channel switch be- forehand. For setting details, refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connec- tion- (Fibre Channel) Fibre Channel Switch Settings" or "Fabric OS Administrator's Guide".

  • Page 10: Creating The Server Accessible Lun Groups (setting The Lun Groups)

    Driver or the Symantec Stor- age Foundation is used ® – Default – – Windows Linux VMware ESX PAN Manager Citrix XenServer Oracle VM Server for HP-UX – HP-UX – – FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-5332-15ENZ0...

  • Page 11: Setting The Host Response For The Eternus Dx8000 S2 Series Using The Eternus Multipath Driver

    – – *1: An Oracle-brand Fibre Channel card driver may be used for Fujitsu Fibre Channel cards. To confirm which driver should be used, check the "Notes" and "Fibre Channel Cards that Require an Ora- cle-brand Driver" sections in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fi- bre Channel) for Oracle Solaris".

  • Page 12: Allocating Lun Groups (setting The Host Affinity)

    Note that changing the "Load Balance" setting has no affect on non-HP-UX servers. 2.2.2.2 Reject INQUIRY from Unauthorized Host Only when using the VERITAS Volume Manager Dynamic Multipathing (VxVM DMP) function, select "Enable". FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-5332-15ENZ0...

  • Page 13: Checking The Wwns

    Checking the WWNs Checking the WWNs Use ETERNUS Web GUI to check the WWN of each ETERNUS DX. They are required for connecting the ETERNUS DX to the server. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-5332-15ENZ0...

  • Page 14

    • operational problems as the result of errors, omissions, or the use of information in this manual. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information • in this manual.

Comments to this Manuals

Symbols: 0
Latest comments: