System Features - Gemini GEM-P801 Installation Instructions Manual

WI1089 GEM-P801 Installation Instructions
indicated at the keypad. The Supervisory
timer is programmable from 1-8 hours; 0
means NO supervision.
Household Fire is enabled, the Wireless
Smoke Supervisory Timer will automatically
be sey to 4 hours.
[18]Test Timer Offset
Enter the time, in hours, that a Test Timer
will be reported after Dealer Mode has been
exited. With the default value of 12, the test
timer will be sent 12 hours after exiting
Dealer Mode. The test timer can also be
offset using PCD-Windows Downloading
Software. On power up the test timer is sent
immediately. Follow the commands below to
offset the test timer using Quickloader
Software:
1 From the Status Screen, select
Miscellaneous
2 Enter the number of hours for Test
Timer Offset
3 Select Set Test Timer Offset
4 Select OK

System Features

[20]Keypad Features 1
(1) Enable Keypad Fire (
Additional Programming required:
Select reporting to Telco 1 [36-1] or Telco 3
[56-1].
14
(2) Enable Keypad AUX (
Additional Programming required:
Select reporting to Telco 1 [36-2] or Telco 3
Note: If UL
[56-2].
(3) Enable Keypad Panic (
Additional Programming required:
Select reporting to Telco 1 [36-3] or Telco 3
[56-3].
(4) Enable Ambush - If enabled, the 8th
User Code will send an Ambush report
when entered to disarm the system.
Additional Programming required:
Program User 8 Arm/Disarm Code.
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
UL Installations: If Keypad Fire [20-1] is
enabled, the keypad must be mounted
within (3) three feet from the Control Panel.
[21]Keypad Features 2
(1) Audible Panic - Keypad Panic will not
turn the Bell on unless this option is
programmed.
(2) Exit/Entry with Urgency - select to give
an audible indication of Exit and Entry
times. During the last 10 seconds of entry
and exit time, the keypad sounds a distinct
sound to indicate the premises must be left
or the panel must be disarmed.
(3) Display Bypassed (Armed) - Select to
)
7G display bypassed zones while the panel is
armed.
(4) Disable Code Entry Beeps - Program
to disable keypad beeping on valid code
and function entries.
)
8G
[22]Miscellaneous Features 1
(1) Abort Delay - Program to allow a 15
second Delay (except 24 Hour Zones) after
)
9G
a zone trip before reporting.
system within 15 seconds to prevent
reporting.
(2)
A0
armed, entering this command allows 3
minutes to Exit through Exit/Entry and Exit/
Entry Follower Zones. Enabling this option
also enables Easy Arm, press the D key to
arm the system.
(3) Swinger Shutdown - Automatically
disables armed zones with excessive alarm/
restores (swingers). Non-24-Hour Protection
zones: allows only 3 alarms and 2 restores
per zone per arming before the zone is
disabled.
(4) Bell on Line Cut (Armed) - Program to
turn the Bell Output on if the telephone line
has been cut while the panel is armed.
[23]Programmable Output Features 1
(1) Audio Verification - Program to activate
the PGM during reporting.
zones for audio verification by programming
the required zones in PGM Output [08],
PGM Features 2 [24] and PGM Features 3
[25]. Connect the PGM to the Veriphone
trigger low input.
(2) Access Output - Activates the PGM
Disarm the
Easy Exit/Easy Arm- Enables
command. While the system is
Select specific
TM