Table of Contents
Advertisement
7.0 - PROGRAMMING THE ALARM SYSTEM
The alarm system has been factory configured but settings can be modified at
any time.
During programming, proceed as follows:
- To enable a function, press textured button '1' => LED will flash once
- To disable a function, press smooth button '2' => LED will flash twice.
To modify settings proceed as follows:
!
With the alarm disarmed, open the driver door and leave it open.
!
Turn ignition key "ON".
!
The status LED will turn ON for 0,5 seconds; while the LED is ON,,
simultaneously press both buttons on the remote control.
!
The turn indicators and the LED will flash twice to confirm the alarm is in
configuration mode.
!
To enable and/or disable the functions, proceed as indicated in the table
below. Keep in mind that each time a button is pressed, the system will go to
the next function.
FUNCTION
DEFAULT setting
Continuous (siren) or
Continuous
intermittent (horn)
CDL 0,5 or 6 sec.
0,5"
25" comfort closure
Disabled
Disabled
Double pulse unlock
Disabled
Current absorption sensor
Anti-distraction rearming and
Disabled
auto-lock
Panic function
Panic/boot release
NB: If
ignition key if turned OFF" during configuration, the system will
"
procedure; the remaining
functions will remain unchanged.
!
The end of the programming procedure is always confirmed by 2 flashes of
the turn indicators and the LED.
!
Turn ignition key "OFF" and close door.
Self-arming of engine immobilizer is factory enabled and
cannot be modified in the version for the UK market.
PAGE 10
This function allows to permanently exclude all acoustic signals. See the
relative paragraph for programming.
If enabled, the PANIC ALARM function allows the user to deliberately activate
the optical/acoustic alarm signals by pressing remote control button 2.
This function works regardless of whether the alarm system is "ON" or "OFF".
The alarm signals last up to approx. 30" but can be silenced by pressing button
2 again. During the alarm signals, the LED will be ON steady.
If during programming, the PANIC function has been disabled, pressing button
2, when the alarm is armed or disarmed, will activate the BOOT RELEASE
function. There will be no confirmation signal if the alarm is disarmed but, if the
alarm is armed, the turn indicators will flash once and the LED will turn ON
BUTTON 1
steady. If the boot is released while the alarm is armed, there will be a 60" delay
BUTTON 2
time for loading/unloading without triggering an alarm. After the delay time, the
Intermittent
Continuous
LED will turn OFF. Pressing button 2, resets the alarm in security mode before
(horn)
(siren)
the end of the 60" delay. The LED will immediately turn OFF.
0,5"
0,6"
Enable
Disable
Disable
Enable
This function activates the alarm system if a voltage change occurs in the
Enable
Disable
Disable
Enable
This function prevents the vehicle from being unintentionally left unprotected if,
Boot
Panic
after the system is armed, it is accidentally disarmed by pressing button 1. The
system automatically rearms if no other activity is detected within 35 sec. (ex.
exit the
door opening, ignition ON). A flash of the turn indicators will confirm self-
rearming. If a door is opened after disarming, the function will be disabled.
The anti-distraction function activates the CDL control. Therefore, in order to
prevent involuntary activation of the alarm system, the driver door switch
MUST be connected to the GREEN/BROWN alarm wire.
The door-lock security function automatically locks all doors 20" after ignition is
turned ON. All doors will automatically unlock when ignition key is turned OFF.
To prevent accidental activation, the system continuously monitors the ignition
key status and DOOR/BOOT SWITCH inputs. It will not allow doors to lock if the
DOORS and BOOT are manually opened after ignition has been turned ON.
8.0 - PROGRAMMABLE FUNCTIONS
8.1 - ACOUSTIC SIGNALS
8.2 - PANIC ALARM OR BOOT RELEASE
There is a 5" interval between one panic alarm cycle and the next.
During the arming delay, button 2 cannot be used to release the boot
because it is used to exclude volumetric sensors and comfort feature.
8.3 - CURRENT ABSORPTION SENSOR
vehicle electrical circuit (ex. lamp switching on).
Before enabling the absorption sensor, check out the rules in force
! !
in your country regarding noise pollution.
8.4 - ANTI-DISTRACTION REARMING AND AUTO LOCK
PAGE11
Advertisement
Table of Contents
