Table of Contents
Advertisement
MIDI Implementation
Model:
D2 (groovebox)
Date:
Mar. 12, 2001
Version:
1.00
Symbol
Description
n
MIDI Channel
vv
Control value
kk
Note Number
xx
ON/OFF
1. Data reception (sound source section)
Channel voice messages
Note Off
status
2nd byte
8nH
kkH
9nH
kkH
vv=Note Off velocity:
00H - 7FH (0 - 127)
Note On
status
2nd byte
9nH
kkH
vv=Note On velocity:
01H - 7FH (1 - 127)
Polyphonic Aftertouch
status
2nd byte
AnH
kkH
vv=Polyphonic Aftertouch:
00 00H - 7FH (0 - 127)
Control Change
* Not received when the Rx Switch parameter is OFF.
Bank Select (Controller number 0,32)
status
2nd byte
BnH
00H
BnH
20H
mm,ll=Bank number:
00 00H–7F 7FH (bank.1–bank.16384)
* Not received when the Rx Program Change Switch or Rx Bank Select Switch parameter
is OFF.
* The Patches corresponding to each Bank Select are as follows.
Bank Select | Program No | Group
MSB | LSB |
|
——————+—————+————————————+————————————————————————————————————————
81
|
0 |
001 - 128 | Preset A
81
|
1 |
001 - 128 | Preset B
81
|
2 |
001 - 128 | Preset C
81
|
3 |
001 - 128 | Preset D
84
|
0 |
001 - 088 | Preset E
85
|
0 |
001 - 128 | User
85
|
1 |
001 - 128 | User
* The Rhythm set corresponding to each Bank Select are as follows.
Bank Select | Program No | Group
MSB | LSB |
|
——————+—————+————————————+————————————————————————————————————————
81
|
0 |
1 - 26
| Preset A
84
|
0 |
1 -
4
| Preset B
85
|
0 |
1 - 20
| User
Modulation (Controller number 1)
status
2nd byte
BnH
01H
* The effect will apply according to the Modulation Control setting.
Data Entry (Controller number 6,38)
status
2nd byte
BnH
06H
BnH
26H
mm,ll= the value of the parameter specified by RPNmm=MSB, ll=LSB
98
Range
0H–6H,9H (ch.1–ch.7,ch.10)
00H–7FH (0–127)
00H–7FH (0–127)
00H–3FH (0–63:OFF), 40H–7FH (64–127:ON)
3rd byte
vvH
00H
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
Patch No.
001 - 128
001 - 128
001 - 128
001 - 128
001 - 088
001 - 128
129 - 256
Patch No.
01 - 26
01 - 04
01 - 20
3rd byte
vvH
3rd byte
mmH
llH
Expression (Controller number 11)
status
2nd byte
BnH
0BH
* Expression messages are used to adjust the volume of each part.
Hold 1 (Controller number 64)
status
2nd byte
BnH
40H
Sostenuto (Controller number 66)
status
2nd byte
BnH
42H
Soft (Controller number 67)
status
2nd byte
BnH
43H
Hold 2 (Controller number 69)
status
2nd byte
BnH
45H
Portamento Control (Controller number 84)
status
2nd byte
BnH
54H
* A Note On message received immediately after a Portamento control will be sounded
with the pitch changing smoothly from the source note number. If a voice is already
sounding at the same note number as the source note number, that voice will change
pitch to the pitch of the newly received Note On, and continue sounding (i.e., will be
played legato).
* The speed of the pitch change caused by Portamento is determined by the Portamento
Time parameter.
RPN MSB/LSB (Controller number 100,101)
status
2nd byte
BnH
65H
BnH
64H
mm=MSB of the parameter number specified by RPN
ll=LSB of the parameter number specified by RPN
<< RPN >>
Control Changes include RPN (Registered Parameter Numbers), which are extended
parameters whose function is defined in the MIDI specification.
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
order) is transmitted to specify the parameter you wish to control. Then, Data Entry
messages (Controller numbers 6 and 38) are used to set the value of the specified parameter.
Once a RPN parameter has been specified, all further Data Entry messages on that channel
are considered to apply to that specified parameter. In order to prevent accidents, when the
desired setting has been made for the parameter, it is recommended that RPN be set to Null.
This device receives the following RPNs.
RPN
Data entry
MSB LSB
MSB LSB
00H 00H
mmH —
mm : 00H–0CH (0–12 semitones)
ll : ignored (processed as 00H)
Up to 1 octave can be specified in semitone steps.
*The Bend Range up parameter, Bend Range Down parameter will
also be changed.
*Not received by the Part R.
00H 01H
mmH llH
mm, ll: 20 00H–40 00H–60 00H ( -4096 x 100 / 8192–0–+4096 x 100 /
8192 cent )
*The Fine Tune parameter of each Part will change.
00H 02H
mmH —
mm : 10H–40H–70H (-48–0–+48 semitones)
ll : ignored (processed as 00H)
*The Key Shift parameter of each Part will change.
7FH 7FH
— —
RPN will be set as "unspecified". Once this setting has been made,
subsequent Data Entry messages will be ignored. (It is not necessary to
transmit Data Entry for RPN Null settings.) Parameter values that
were previously set will not change.
mm, ll: ignored
* For the functions of other controller numbers, refer to "Table of Transmitted Data" (p. 76).
3rd byte
vvH
3rd byte
xxH
3rd byte
xxH
3rd byte
xxH
3rd byte
xxH
3rd byte
kkH
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
Master Fine Tuning
Master Coarse Tuning
RPN null
Advertisement
Table of Contents
