Table of Contents
Advertisement
14. Phaser (Modulate the Sound)
By adding a phase-shifted sound to the original sound, this effect modulates the sound to add depth and a sense of rotation.
Screen
Parameter
MANUAL
DEPTH
RESONANCE
RATE
MIX
(Mix Level)
OUTPUT PAN
OUTPUT LEVEL
* 1: 16 (16th note), 8T (8th note triplets), 16. (dotted 16th note), 8 (8th note), 4T (quarter note triplets), 8. (dotted 8th note), 4 (quarter note), 2T (half note
triplets), 4. (dotted quarter note), 2 (half note), 1T (whole note triplets), 2. (dotted half note), 1 (whole note)
* 2: 2M (2 measures), 3M (3 measures), 4M (4 measures), 8M (8 measures), 16M (16 measures)
15. Chorus (Add Spaciousness and Depth to the Sound)
This effect creates an impression of multiple sound sources in unison (Chorus effect), giving spaciousness and depth to the sound.
Screen
Parameter
PRE DELAY
(Pre Delay Time)
DEPTH
PHASE
RATE
FILTER TYPE
CUTOFF
(Cutoff Frequency)
BALANCE
(Effect Balance)
OUTPUT LEVEL
* 1: 16 (16th note), 8T (8th note triplets), 16. (dotted 16th note), 8 (8th note), 4T (quarter note triplets), 8. (dotted 8th note), 4 (quarter note), 2T (half note
triplets), 4. (dotted quarter note), 2 (half note), 1T (whole note triplets), 2. (dotted half note), 1 (whole note)
* 2: 2M (2 measures), 3M (3 measures), 4M (4 measures), 8M (8 measures), 16M (16 measures)
Chapter 4. Applying Effects to the Sound (Effects)
Explanation
Specifies the center frequency at which the sound will be modulated.
Specifies the depth of modulation.
This setting emphasizes the frequency range in the vicinity of the cen-
ter frequency.
Specifies the frequency of modulation. If a note value or measure is
selected as the value of this parameter, the Rate will synchronize with
the BPM of the pattern at intervals of the specified note value or mea-
sure.
Adjusts the proportion of the original sound that will be combined
with the phase-shifted sound.
Specifies the stereo location of the output from the Phaser effect.
Specifies the output volume of the Phaser effect.
Explanation
Specifies the time from the original sound until
when the chorus sound is heard.
Specifies the depth of modulation.
Adjusts the spaciousness of the sound.As this
setting is increased, the sound will spread more
toward left and right.
Specifies the rate of modulation. If a note value
or measure is selected as the value of this param-
eter, the Rate will synchronize with the BPM of
the pattern at intervals of the specified note val-
ue or measure.
Determines the type of filter that will be applied
to the chorus sound.
Specifies the cutoff frequency of the filter.
Adjusts the volume balance between the origi-
nal sound and the chorus sound.With a setting
of "0," no chorus sound will be output.
Specifies the output volume from the stereo cho-
rus.
Value
100 (Hz)–8.00 (kHz)
0–127
0–127
0.1–10.0 (Hz), notes
(*1), measures (*2)
0–127
L64–R63
0–127
Value
0.0–100
0–127
0–180
0.1–10.0 (Hz), notes (*1), measures
(*2)
OFF (a filter will not be used),
LPF (the frequency range above the
cutoff frequency will be cut),
HPF (the frequency range below the
cutoff frequency will be cut)
200 (Hz)–8.00 (kHz)
0–100 (%)
0–127
Y
X
Y
X
51
Advertisement
Table of Contents
