Table of Contents
Advertisement
Hold 2 (Controller number 69)
status
2nd byte
BnH
45H
Portamento control (Controller number 84)
status
2nd byte
BnH
54H
* For the functions of other controller numbers, refer to "Table of Transmitted Data" (p. 76).
Program Change
status
2nd byte
CnH
ppH
pp=Program number:
00H - 7FH (prog.1 - prog.128)
* This message is not transmitted when the Tx Program Change Switch parameter is OFF.
System Realtime messages
Active Sensing
status
FEH
* Transmitted at intervals of approximately 250ms.
System Exclusive messages
Universal Non-realtime System Exclusive Messages
Identity Reply
Status
Data byte
F0H
7EH, dev, 06H, 02H, 41H, 0BH, 01H,
03H, 00H, 00H, 03H, 00H, 00H
Byte
Explanation
F0H
Exclusive status
7EH
ID number (universal non-realtime message)
dev
Device ID (dev:10H(17)-1FH(32))
06H
Sub ID#1 (General Information)
02H
Sub ID#2 (Identity Reply)
41H
ID number (Roland)
0BH 01H
Device family code
03H 00H
Device family number code
00H 03H 00H 00H
Software revision level
F7H
EOX (End of Exclusive)
* When Identity Request is received, Identity Reply message will be transmitted.
Data Set 1
DT1
status
data byte
F0H
41H, dev, 00H, 0BH, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte
Remarks
F0H
Exclusive status
41H
ID number (Roland)
dev
device ID (dev: 10H–1FH)
00H
model ID (D2)
0BH
model ID (D2)
12H
command ID (DT1)
aaH
address MSB
bbH
address
ccH
address
ddH
address LSB
eeH
data: The actual data to be transmitted. Multi-byte data is transmitted
in the order of the address.
:
:
ffH
data
sum
checksum
F7H
EOX (End Of Exclusive)
* For the address, size, and checksum, refer to "Examples of system exclusive messages
and calculating the checksum" (p. 107).
* Data whose size is greater than 128 bytes should be divided into packets of 128 bytes or
less and transmitted. Successive "Data Set 1" messages should have at least 20 ms of
time interval between them.
3rd byte
xxH
3rd byte
kkH
Status
F7H
status
F7H
MIDI Implementation
Data Set 1
DT1
status
data byte
F0H
41H, dev, 3AH, 12H, aaH,
bbH, ccH, ddH, sum
Byte
Remarks
F0H
Exclusive status
41H
ID number (Roland)
dev
device ID (dev: 10H–1FH)
3AH
model ID (D2 Quick)
12H
command ID (DT1)
aaH
address (Status/Channel)
bbH
address/Data H
ccH
Data L
ddH
Data E
sum
checksum
F7H
EOX (End Of Exclusive)
* For the address, size, and checksum, refer to "Examples of system exclusive messages
and calculating the checksum" (p. 107).
* Transmission of consecutive addresses is not possible.
3. Data reception (Sequencer section)
3.1 Messages recorded during recording
Channel voice messages
Note Off
status
2nd byte
8nH
kkH
9nH
kkH
Note On
status
2nd byte
9nH
kkH
vv=Note On velocity:
01H - 7FH (1 - 127)
Polyphonic Aftertouch
status
2nd byte
AnH
kkH
Control Change
status
2nd byte
BnH
kkH
kk=control number:
00H–78H (0–120)
Program Change
status
2nd byte
CnH
ppH
pp=Program number:
00H–7FH (prog.1–prog.128)
Channel Aftertouch
status
2nd byte
DnH
vvH
Pitch Bend Change
status
2nd byte
EnH
llH
mm,ll=Pitch Bend value:
00 00H–40 00H–7F 7FH (-8192–0–+8191)
Channel Mode messages
All Sound Off (Controller number 120)
status
2nd byte
BnH
78H
Reset All Controllers (Controller number 121)
status
2nd byte
BnH
79H
status
F7H
3rd byte
vvH
00H
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
3rd byte
00H
3rd byte
00H
101
Advertisement
Table of Contents
