Icom IC-775DSP Instruction Manual page 9

@ VFO/MEMORY SWITCH for SUB readout
[VFO/MEMO]
Toggles SUB readout operating mode between
the VFO mode and memory mode.
@ MEMORY UP/DOWN SWITCHES for SUB
readout [SUB M-CH DN]/[SUB M-CH UP]
e Select the memory channel number for SUB
readout.
- Memory channels can be selected both in the VFO
and memory modes.
e Change the transmit frequency in programmed
kHz steps while in channelized split operation.
(p. 34)
@ SET SWITCH [SET] (p. 41)
e Enters P-set (push-set) mode when pushed.
e Enters H-set (hold-set) mode when pushed and
held for 2 sec.
-The set modes are used to adjust EE
changed settings.
@ DUALWATCH SWITCH [DUALWATCH] (p. 35)
e Turns the dualwatch tuneton ON and OFF when
pushed.
e Turns the dualwatch function ON and equalizes
the SUB readout frequency to the MAIN readout
when pushed for 2 sec. (p. 46)
@ FREQUENCY-INPUT SWITCHES [MAIN F-INP]/
[SUB F-INP] (p. 25)
Enable the keypad to input a frequency.
- The frequency readout disappears when pushed; and
the keypad can be used to enter a frequency directly.
- To cancel the frequency input, push this switch again.
@ SPLIT SWITCH [SPLIT] (p. 33)
e Turns the split frequency function ON and OFF
when pushed momentarily. .
- Transmit frequency and "(SPLIT)" appear in the SUB
readout. The SUB readout blinks 4 times to show
the SUB readout is used for transmitting when the
function is ON.
e Turns the split frequency function ON and
equalizes the SUB readout frequency (transmit
frequency) to the receive frequency when
pushed for 2 sec.
- Split shift frequency can be pre-programmed to
save time when DX'ing. (p. 33)
- When pushed together with [XFC] for 2 sec., the
MAIN readout frequency (receive frequency) is
equalized to the transmit frequency.
e Once the split frequency function is ON,
equalizes the transmit frequency to the receive
frequency and enters channelized split opera-
tion when pushed for 2 sec.
e Activates the subaudible tone encoder and split
frequency function when pushed in FM mode.
PANEL DESCRIPTION 1
@ QUICK TUNING SWITCH [TS] (p. 26)
e Turns the quick tuning step ON and OFF.
- While this indicator is displayed, the frequency can
be changed in programmed kHz steps.
- The SUB readout frequency is also chenided in the
programmed kHz steps.
Quick tuning indication
ie l
e When pushed for 2 sec., turns the 1 Hz step ON
and OFF.
- 1 Hz indication appears in the MAIN readout and
the frequency can be changed in 1 Hz steps.
- The SUB readout frequency can also be changed in
ES Hz step indication
ri VFO
1 Hz steps.
@ TRANSMIT FREQUENCY CHECK SWITCH
[XFC] (pgs. 33, 34, 38)
Monitors the transmit frequency when pushed and
held when the split frequency function is ON.
- While pushing this switch, the transmit frequency can
be changed with the main dial, keypad, memo pad, or
the [A UP]/[V DOWN] switches.
@ MEMORY UP/DOWN SWITCHES for MAIN
readout [MAIN M-CH DOWN]/[MAIN M-CH UP]
Select the memory channel number for MAIN
readout. (p. 49)
- Memory channels can be selected both in the VFO
and memory modes.
@ VFO/MEMORY SWITCH for MAIN readout
[VFO/MEMO] (p. 49) |
Toggles MAIN readout operating mode between
the VFO mode and memory mode.
@ SUB TX/RX INDICATOR [SUB]
e Lights up in green while receiving a signal on
the SUB readout and when the squelch is open.
e Lights up in red while transmitting on the SUB
` readout frequency during split Mequency opera-
tion.
@ MAIN TX/RX INDICATOR [MAIN]
e Lights up in green while receiving a signal on
the MAIN readout and when the squelch is
open.
e Lights up in red while transmitting on the MAIN
readout frequency.