D: References - Omron J1000 User Manual

No. Name
Selects the carrier frequency
1 : 2.0 kHz
2 : 5.0 kHz
3 : 8.0 kHz
Carrier Frequency 4 : 10.0 kHz
C6-02
Selection 5 : 12.5 kHz
6 : 15.0 kHz
7 : Swing PWM
8 to E : No setting possible
F : User defined (determined by C6-03 through C6-05)
C6-03 Carrier Frequency C6-03 and C6-04 set upper and lower limits for the carrier
Upper Limit frequency.
C6-04 Carrier Frequency
Lower Limit
The coefficient K depends on C6-03:
C6-03 ≥ 10.0 kHz: K = 3
10.0 kHz > C6-03 ≥ 5.0 kHz: K = 2
5.0 kHz > C6-03: K = 1
When C6-05 ≤ 6, C6-04 is disabled (makes the carrier frequency
C6-03 value).
C6-05 Carrier Frequency Sets the relationship of output frequency to carrier frequency when
Proportional Gain C6-02 = F.
<8> Default setting value is dependent on parameter C6-02, Carrier Frequency Selection.
<22> Parameter can be changed during run.
<57> Default setting value is dependent on parameter o2-04, Drive Model Selection and C6-01, Drive Duty Selection.
u

d: References

Reference parameters are used to set the various frequency reference values during operation.
No. Name
d1-01
Frequency
Frequency reference
<22>
Reference 1
d1-02
Frequency Frequency reference when digital input "Multi-Step Speed
<22>
Reference 2 Reference 1" (H1- = 3) is on.
d1-03
Frequency Frequency reference when digital input "Multi-Step Speed
<22>
Reference 3 Reference 2" (H1- = 4) is on.
d1-04
Frequency Frequency reference when digital inputs "Multi-Step Speed
<22>
Reference 4 Reference 1, 2" (H1- = 3 and 4) are on.
d1-05
Frequency Frequency reference when digital input "Multi-Step Speed
<22> Reference 5 Reference 3" (H1- = 5) is on.
d1-06
Frequency Frequency reference when digital inputs "Multi-Step Speed
<22>
Reference 6 Reference 1, 3 " (H1- = 3 and 5) are on.
d1-07
Frequency Frequency reference when digital inputs "Multi-Step Speed
<22>
Reference 7 Reference 2, 3" (H1- = 4 and 5) are on.
d1-08
Frequency Frequency reference when multi-function input "Multi-Step speed
<22>
Reference 8 reference 1, 2, 3" (H1- = 3, 4, 5) are on.
d1-17
Jog Frequency Frequency reference when digital inputs "Jog Frequency
<22>
Reference Reference", "Forward Jog" or "Reverse Jog." are on.
Sets the frequency reference upper limit as a percentage of
Frequency
maximum output frequency (E1-04). Output speed is limited to this
d2-01 Reference Upper
value even if the frequency reference is higher. This limit applies
Limit
to all frequency reference sources.
Sets the frequency reference lower limit as a percentage of
Frequency
maximum output frequency (E1-04). Output speed is limited to this
d2-02 Reference Lower
value even if the frequency reference is lower. This limit applies to
Limit
all frequency reference sources.
SIEP C710606 33A OYMC AC Drive – J1000 User Manual
Description
carrier frequency
C6-03
C6-04
output frequency
× (C6-05) × K
E1-04
max output
frequency
Description
d1: Frequency Reference
Use d1 parameters to configure the drive frequency reference.
d2: Frequency Upper and Lower Limits
Use d2 parameters to configure the frequency reference limits.
d3: Jump Frequency
Use d3 parameters to configure the drive Jump Frequency settings.
Range
1 to F
1.0 to 15.0
output
frequency
1.0 to 15.0
00 to 99
Range
0.00 to
400.00 Hz
<19>
0.0 to 110.0 100.0%
0.0 to 110.0 0.0%
B.2 Parameter Table
Addr.
Def. Mode
Hex
<57>
S 224
<8>
O 225
<8>
O 226
<8>
O 227
Addr.
Def. Mode
Hex
0.00 Hz S 280
0.00 Hz S 281
0.00 Hz S 282
0.00 Hz S 283
0.00 Hz O 284
0.00 Hz O 285
0.00 Hz O 286
0.00 Hz O 287
6.00 Hz S 292
O 289
O 28A
Pg.
79
80
80
80
Pg.
82
82
82
82
82
82
82
82
82
83
83
B
173