Diagnostics And Troubleshooting - Invertek Drives Optidrive E3 ODE-3 Series User Manual

10.8.1.3. Configuration Switches – MAC ID
MAC ID Switch 3
0 OFF
1 OFF
2 OFF
3-62 ...
63 ON
Bottom View
PC Connector:
1. GND
2. GND
3. RS232 Rx 32 Rx
4. RS232 Tx 32 Tx
5 5
9 9
6 6
1 1
Power:
1. +24 V DC +24 V DC
1 1
2. GND 2. GND
2 2
10.8.2. DeviceNet Master Configuration 10.8.2. DeviceNet Master Configuration
The latest version of the EDS file may be downloaded from the HMS website, www.anybus.com. The latest version of the EDS file may be downloaded from the HMS website, www.anybus.com.
The actual configuration process will differ for different DeviceNet Master Systems and is not possible to explain in this document. The actual configuration process will differ for different DeviceNet Master Systems and is not possible to explain in this document.
Example configurations for Rockwell PLC are provided on the HMS website. Example configurations for Rockwell PLC are provided on the HMS website.
When configuring the communication between the Master System and the gateway, 4 words of Input Process Data and 4 words When configuring the communication between the Master System and the gateway, 4 words of Input Process Data and 4 words
of Output Process Data should be allocated per drive connected the gateway, up to a maximum of 32 Input and Output words. If of Output Process Data should be allocated per drive connected the gateway, up to a maximum of 32 Input and Output words. If
necessary, a configuration may be chosen in the Master which supports more than the connected number of drives, e.g. if 3 drives are necessary, a configuration may be chosen in the Master which supports more than the connected number of drives, e.g. if 3 drives are
connected to the gateway, the Master System can be configured for 12, 16 or even 32 words of Input and Output process data. The connected to the gateway, the Master System can be configured for 12, 16 or even 32 words of Input and Output process data. The
additional words will simply not contain any data. additional words will simply not contain any data.

10.9. Diagnostics and Troubleshooting

10.9. Diagnostics and Troubleshooting
Symptom Symptom
No Communication, Master > Gateway No Communication, Master > Gateway No Communication, Master > Gateway
Profibus Communication OK,
Not possible to control the Optidrive(s)
www.invertekdrives.com
Switch 4 Switch 5
OFF OFF
OFF OFF
OFF OFF
... ...
ON ON
DB9
1
+5V
2
RS232 Rx (Not Used)
1
3
RS232 Tx (Not Used)
4 4
4 4
NC NC
5 5
Signal 0V Signal 0V
8 8
RS485+ Modbus RTU RS485+ Modbus RTU
9 9
RS485- Modbus RTU RS485- Modbus RTU
Power Power
1 1
+24VDC, 300mA +24VDC, 300mA
2 2
0V 0V
Suggested Actions Suggested Actions
Check all network cables Check all network cables Check all network cables
Check correct bus termination Check correct bus termination
Check correct node address on gateway Check correct node address on gateway
Check GSD / EDS file is recognised and used by the Master Check GSD / EDS file is recognised and used by the Master
Check the Status LEDs 1 and 2 Check the Status LEDs 1 and 2
Check the subnetwork Status LED
Check all sub network connections
Check correct baud rate set in drives
Check drives are addressed sequentially from 1
Check that data is written to the correct memory area(s)
Switch 6 Switch 7
OFF OFF
OFF OFF
OFF ON
... ...
ON ON
DeviceNet Connector
1
Version 1.02 | Fieldbus Guide | 53
Switch 8
OFF
ON
OFF
...
ON
Pin no Description
1
V-
2
CAN L
3
Shield
5
4 4
CAN H CAN H
5 5
V+ V+
10