Polyend Tracker Mini Manual page 130

11
MIDI
11.7 MIDI CC In
Control change messages can be received by Tracker Mini. The CC In
would need to be set in the [Menu] > Config > MIDI menu along with the CC
In channel for the MIDI channel. The MIDI CC Mapping within Tracker Mini
has a set of pre-defined destinations for CC messages.
CC # Function CC # Function
41 Performance Effect Track 1 Pattern Select 71
42 Performance Effect Track 2 Pattern Select 72
43 Performance Effect Track 3 Pattern Select 73
44 74
Performance Effect Track 4 Pattern Select
45 75
Performance Effect Track 5 Pattern Select
46 Performance Effect Track 6 Pattern Select 76
47 Performance Effect Track 7 Pattern Select 77
48 Performance Effect Track 8 Pattern Select 78
51 Performance Effect Slot 1 Value - Top Row 79
52 80
Performance Effect Slot 2 Value - Top Row
53 81
Performance Effect Slot 3 Value - Top Row
54 Performance Effect Slot 4 Value - Top Row 82
55 Performance Effect Slot 5 Value - Top Row
56 Performance Effect Slot 6 Value - Top Row
57 Performance Effect Slot 7 Value - Top Row
58
Performance Effect Slot 8 Value - Top Row
59
Performance Effect Slot 9 - Top Row
60 Performance Effect Slot 10 Value - Top Row
61 Performance Effect Slot 11 Value - Top Row
62 Performance Effect Slot 12 Value - Top Row
258
Master - Track Mixer Track 1 Volume Level
Master - Track Mixer Track 2 Volume Level
Master - Track Mixer Track 3 Volume Level
Master - Track Mixer Track 4 Volume Level
Master - Track Mixer Track 5 Volume Level
Master - Track Mixer Track 6 Volume Level
Master - Track Mixer Track 7 Volume Level
Master - Track Mixer Track 8 Volume Level
Master - Global Mixer Delay Mix
Master - Global Mixer Reverb Mix
Master - Global Mixer Dry Mix
Master - Global Mixer Line Input
Polyend Tracker Mini Manual
NOTES NOTES
Polyend Tracker Mini Manual
11.8 Program Change
Tracker Mini has the ability to send program change messages. These are
MIDI standard messages which trigger a change to the current 'program' of
an external device by switching presets or configurations. This of course
will be dependant on the program / bank / preset structure and operation of
the receiving device. Often synths use banks and presets so the behaviour
of the device from a program change may vary.
Program change is configured as a CC parameter using number 129.
Example
Pattern 1
Track 3 Track 4
D6 03 ---- ---- D6 03 ---- ----
MIDI Channel 1, with a Program Change, 129
D4 04 D6 M01 a 01
---- ---- ---- assigned to CC A. The value will trigger the
program selection, in this example 01.
D4 04 ---- C 50 D6 03 ---- ----
D4 04 ---- ---- D6 03 ---- V 65
D6 03 ---- ---- D6 03 ---- ----
MIDI Channel 1, with a Program Change, 129
D4 04 M01 a 02
---- ---- -- ---- assigned to CC A. The value will trigger the
program selection, in this example 02.
D4 04 ---- C 50 D6 03 ---- ----
A Program Change is activated slightly ahead of
D4 04 -- M01 m 50 a 03
---- ---- the note. However it may be better to trigger the
program change on a step prior to the note step
or at the end of a previous pattern sequence and
use micro move 'm' to adjust the timing.
Pattern 2
Track 3 Track 4
D6 03 ---- ---- D6 M01 ---- ----
D4 04 E6 03 V 50
---- ---- ----
D4 04 ---- C 50 G6 M01 ---- ----
D4 04 D6 03 V 65
---- ---- ----
The receiving device may have a configuration
that is not an exact match. For example a
program may start at 1 rather than 0. The offset
may need to be taken into account in the Tracker
Mini step program change message.
11
MIDI
259