Table of Contents
Advertisement
Settings Common to All Modes (System Mode)
SYSTEM Com USB Setting window
USB Mode: Selects the mode in which the USB connector will
be used.
Storage: Storage mode. Select this if you want to transfer
files.
MIDI: MIDI mode. Select this if you want to exchange
MIDI messages with a sequencer or other program.
* You must switch the USB Mode before you connect the VC-2
(V-Synth) to your computer via the USB cable. If you change
this setting while the VC-2 (V-Synth) is connected, the
computer may fail to recognize it correctly.
For details on connections to your computer in each USB
Mode, refer to "Backing Up Data to Your
Computer" (p. 40).
USB-MIDI Thru Sw: When USB Mode is set to "MIDI," this
switch specifies whether MIDI messages received at the MIDI
connector will be re-transmitted from the MIDI OUT
connector (ON) or not (OFF).
Chord Memory
Parameter
Value
Explanation
Chord
OFF,
Switches the Multi Chord Memory (one-
Memory
ON
finger chord) function on/off.
Sw
* If you want to synchronize to an exter-
nal device, set Clock Source (p. 35) to EX-
TERNAL, then get your external device
to transmit clock messages. If you fail to
do this, chords will not play correctly.
Grid Reso-
Dot-
Each note within the chord will be played
lution
ted 8th
separately at the timing interval you
note–
specify here.
64th
note
Code set
C–B
Specify a chord for each key in the range
C–B.
KEEP
OFF,
When entering a chord from the key-
ON
board, this parameter specifies whether
the keys you press will be held in their
pressed state (ON) or not (OFF). If this is
ON, the key will be maintained in a
"pressed" state even when you release it.
STORE
—
Store the chord you specified from the
keyboard into the chord set.
36
Controller Settings (Controller)
Tx
Parameter
Value
Explanation
Patch Tx
1–16,
Specifies the transmit channel of MIDI
Ch
RX CH,
messages in Patch mode. If you do not
OFF
want to transmit MIDI messages to ex-
ternal MIDI devices, turn this parameter
"OFF." If you want the transmit channel
to always match the Patch Receive
Channel, set this parameter to "RX CH."
Tx PC
OFF,
Specifies whether Program Change mes-
ON
sages will be transmitted (ON) or not
(OFF).
Tx Bank
OFF,
Specifies whether Bank Select messages
ON
will be transmitted (ON) or not (OFF).
Tx Active
OFF,
Specifies whether Active Sensing mes-
Sens
ON
sages will be transmitted (ON) or not
(OFF).
KBD
Parameter
Value
KBD Sens
LIGHT,
MEDIUM,
HEAVY
KBD Veloc-
REAL,
ity
1–127
After Sens
0–200
Local Sw
OFF, ON
Explanation
Adjusts the keyboard's touch.
LIGHT: Light weight synthesizer key-
board like
MEDIUM: Standard
HEAVY: Acoustic piano simulation
Specifies the velocity value that will
be transmitted when you play the
keyboard. If you want actual key-
board velocity to be transmitted, set
this to "REAL." If you want a fixed
velocity value to be transmitted re-
gardless of how you play, specify the
desired value (1-127).
Specifies the Aftertouch sensitivity.
Higher values will allow Aftertouch
to be applied more easily. Normally
you will leave this at "100."
The Local Switch determines whether
the internal sound generator is dis-
connected (OFF) from the controller
section (keyboard, pitch bend/modu-
lation lever, knobs, buttons, Time
Trip Pad, D Beam controller, pedal,
and so on); or not disconnected (ON).
Normally this is left "ON," but if you
wish to use the V-Synth's keyboard
and controllers to control only exter-
nal sound modules, set it to "OFF."
Advertisement
Table of Contents
