Functions Of System Parameters; Settings Common To The Entire System (Common) - Roland VC-2 Owner's Manual

This indicates the version of the VC-2.
3. Touch <EXIT> to close the window.
Functions of System
Parameters
This section explains what the different System parameters
do, and also how these parameters are organized.
Settings Common to the Entire
System (Common)
Master
Parameter Value Explanation
Master 415.3– Adjusts the overall tuning of the VC-2.
Tune 466.2 The display shows the frequency of the
Hz A4 note (center A).
Master Key -24– Shifts the overall pitch of the VC-2 in
Shift +24 semitone steps.
Master 0–127 Adjusts the volume of the entire VC-2.
Level
IO
Parameter Value Explanation
Output -12– This adjusts the output gain from the VC-
Gain +12 2's Analog Out and Digital Out. When, for
dB example, there are relatively few voices
being sounded, boosting the output gain
can let you attain the most suitable output
level for recording and other purposes.
Digital 44.1, Sets the sampling frequency of the digital
Output 48, 96 output.
Freq KHz
EQ
Parameter Value
2 Band EQ OFF, ON
LOW Freq 50, 63, 80, 100,
125, 160, 200,
250, 315, 400,
500, 630, 800,
1000, 1250, 1600,
2000, 2500, 3150,
4000 Hz
LOW Gain -15– +15 dB
Explanation
Switch the 2-Band equalizer
on/off.
Selects the frequency of the low
range.
Adjusts the gain of the low fre-
quency. Positive (+) settings
will emphasize the low-fre-
quency range.
Settings Common to All Modes (System Mode)
Parameter Value
HIGH Freq 2000, 4000, 5000,
6300, 8000,
10000, 12500,
16000, 20000 Hz
HIGH Gain -15– +15 dB
TOTAL -15– +15 dB
Gain
MIDI/USB
Parameter Value
Device ID 17–32
Clock INTERNAL,
Source EXTERNAL
Rx Sw OFF, ON
Rx Channel 1–16
Rx PC OFF, ON
Rx Bank OFF, ON
Rx Sys-Ex OFF, ON
Tx Edit OFF, ON
Clock Out OFF, ON
USB Setup —
Volume OFF, ON
Expression
Level Con-
trol
Explanation
Selects the frequency of the high
range.
Adjusts the gain of the high fre-
quency. Positive (+) settings
will emphasize the high-fre-
quency range.
Adjusts the total gain.
Explanation
When you want to transmit or re-
ceive System Exclusive messages,
set this parameter to match the De-
vice ID number of the other MIDI
device.
The LFO cycle or multi-effects
changes can be synchronized to a
clock (tempo). When this is used
by the patch, this Clock Source set-
ting determines the clock which
will be used.
INTERNAL: The Patch Tempo will
be used.
EXTERNAL: Synchronize to the
clock of an external sequencer.
Specifies whether all MIDI mes-
sages will be received (ON) or not
(OFF).
Sets the Basic Channel (MIDI chan-
nel on which the VC-2 receives and
transmits messages).
Specifies whether Program
Change messages will be received
(ON) or not (OFF).
Specifies whether Bank Select mes-
sages will be received (ON) or not
(OFF).
Specifies whether System Exclu-
sive messages will be received
(ON) or not (OFF).
Specify whether changes you
make in the settings of a patch will
be transmitted as system exclusive
messages (ON), or will not be
transmitted (OFF).
Specifies whether MIDI clock will
be transmitted (ON) or not (OFF).
The SYSTEM Com USB Setting
window appears.
Specifies whether received Vol-
ume or Expression Pedal messages
will adjust the output volume
(ON), or will be ignored (OFF).
35