General Network Settings - Grandstream Networks GXV3350 Administration Manual

Preferred Internet Protocol: Selects which Internet protocol to use. When both IPv4 and IPv6 are enabled, phone
attempts to use preferred protocol first and switches to the other choice if it fails.
IPv4 Settings: Here user can configure the IPv4 address type for both data and VoIP calls. For network configuration of
data, if DHCP is selected, the phone will get an IP address automatically from the DHCP server in the network. This is the
default mode. If Static IP is selected, manually enter the information for IP Address, Subnet Mask, Default Gateway, DNS
Server and Alternative DNS server. If PPPoE is selected, type PPPoE Account ID and PPPoE Password provided from the
PPPoE server to get authenticated for network access. For network configuration of VoIP calls, if DHCP is selected, the
phone will get an IP address automatically from the DHCP server in the network. This is the default mode. If Static IP is
selected, manually enter the information for IP Address, Subnet Mask, Default Gateway, DNS Server and Alternative DNS
server.
IPv6 Settings: Here user can configure the IPv6 address type only for data. If DHCP is selected, the phone will get an IP
address automatically from the DHCP server in the network. This is the default mode. If Static IP is selected, manually
enter the information for IP Address, Prefix Length, DNS Server and Alternative DNS server.
802.1x mode: This option allows the user to enable/disable 802.1x mode on the phone. The default setting is disabled. To
enable 802.1x mode, select the 802.1x mode and enter the required configuration depending on the 802.1x mode chosen.
The available modes are EAP-MD5, EAP-TLS and EAP-PEAP
Wi-Fi
Tap on "Wi-Fi" to turn on/off Wi-Fi connection. By default, it's turned off.
Preferred Internet Protocol: Selects which Internet protocol to use. When both IPv4 and IPv6 are enabled, phone
attempts to use preferred protocol first and switches to the other choice if it fails.
Tap on "Wi-Fi Band" to set the type of WiFi Band ("2.4G", "5G" or "2.4G&5G"). The default setting is 2.4G&5G.
Tap on "Wi-Fi Settings" to set up and manage wireless access points. This option is available only when Wi-Fi is turned
on.
Add Network. If the Wi-Fi network SSID doesn't show up in the list, or users would like to set up advanced options for
the Wi-Fi network, roll to the end of the WiFi list and select "Add Network". Then Enter SSID, Security type, password and
set up address type (DHCP/Static IP/PPPoE) in the prompt dialog. The phone will reboot with Wi-Fi network connected.
Refresh. Press MENU button
Advanced Settings. Press MENU button
Install Certificates. This is to install certificates (previously download/uploaded to the phone) when connecting to
Wi-Fi network requesting SSL certificate.
Wi-Fi Direct. This is to set up peer-to-peer connection between two Wi-Fi Direct devices so that they can share data
and sync files. Press MENU button
displaied.
Wi-Fi Configuration
Saved Networks: this is to show all the Wi-Fi Networks that are registered on the phone.
Network notification: If enabled, the phone will show notification on the top status bar indicating an open network
is available. By default it's enabled.
MAC address: This shows the MAC address of the WiFi.
IP address: This shows the IP address of the phone from Wi-Fi network.
VPN
Enable / Disable OpenVPN®.

General Network Settings

LLDP
Turn on/off LLDP on the GXV3350. If turned on, the phone will be able to discover the LAN polices as set up in the switch side
to obtain network settings such as VLAN tag, Layer 2 QoS 802.1p priority and Layer 3 QoS in a plug-and-play manner.
LLDP TX Interval
and select "Refresh" to initiate scan for the Wi-Fi network within the range.
and select "Advanced".
and select "Advanced". Then tap on "Wi-FI Direct", the Available devices will be