Related Manuals for Allied Telesis GS910/XST Series
Summary of Contents for Allied Telesis GS910/XST Series
- Page 1 GS910/XST Series 10 GIGABIT ETHERNET UNMANAGED SWITCHES GS910/10XST GS910/18XST GS910/26XST Installation and User’s Guide 613-003021 Rev. B...
- Page 2 Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages.
- Page 3 Electrical Safety and Emissions Standards This section contains the following: “US Federal Communications Commission” “Industry Canada” “Safety, Electro Magnetic interference, and Electro Magnetic Susceptibility” on page 4 “Translated Safety Statements” on page 4 US Federal Communications Commission Radiated Energy Note This equipment has been tested and found to comply with the limits for a Class A digital device...
- Page 4 In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Translated Safety Statements Important: The indicates that translations of the safety statement are available in the PDF document Translated Safety Statements posted on the Allied Telesis website at alliedtelesis.com/support.
-
Page 5: Table Of Contents
Contents Preface ....................................7 Safety Symbols Used in this Document ..........................8 Contacting Allied Telesis ..............................9 Chapter 1: Product Description ............................11 Overview ..................................12 Key Features ................................12 Components ..................................14 Front Panels ................................14 Back Panel ................................15 10/100/1000 Base-T Twisted Pair Ports ........................ 15 100Base-TX, 1G/2.5G/5G/10G Base-T Twisted Pair Ports ................... - Page 6 Contents Installing a Switch Using the BRKT-J22 Wall Mount Kit ....................49 What to Prepare ..............................49 Installing a Switch with the Front Panel Facing Sideways..................49 Installing a Switch Facing Up ..........................54 Chapter 4: Wall Installation Using the BRKT-J24 Kit .....................57 Unpacking the BRKT-J24 Wall Mount Kit ........................58 Installing the Switch on a Wall Using the BRKT-J24 Brackets ..................59 What to Prepare for Wall Installation ........................59 Installing the Switch on a Wall..........................59...
-
Page 7: Preface
Preface This manual is the installation and user’s guide for the GS910/XST Series 10 Gigabit Ethernet Unmanaged Switches. The switch models included in this manual are: GS910/10XST GS910/18XST GS910/26XST This Preface contains the following sections: “Safety Symbols Used in this Document” on page 8 ... -
Page 8: Safety Symbols Used In This Document
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Safety Symbols Used in this Document This document uses the following conventions: Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. -
Page 9: Contacting Allied Telesis
Preface Contacting Allied Telesis If you need Allied Telesis technical support, visit www.alliedtelesis.com/support. - Page 10 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide...
-
Page 11: Chapter 1: Product Description
Chapter 1 Product Description This chapter contains the follows sections: “Overview” on page 12 “Components” on page 14 “Loop Prevention” on page 24 “Energy Efficiency Ethernet (EEE)” on page 28 “Ethernet Switching Basics” on page 29 ... -
Page 12: Overview
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Overview The GS910/XST Series Switches are eco-friendly unmanaged switches with one SFP/SFP+ uplink port, one 100M/1G/2.5G/5G/10Gigabit uplink port, and 8, 16 or 24 ports of 10/100/1000Mbps. The switch provides a simple solution to integrate 10, 100, and 1000Mbps devices that exist in your network and expand the network to up to 10Gigabit speed. - Page 13 Chapter 1: Product Description IEEE802.3u compliant for 100Base-TX IEEE802.3ab compliant for 1000Base-T IEEE802.3bz compliant for 2.5GBase-T and 5GBase-T IEEE802.3an compliant for 10Gbps Ethernet Auto-Negotiation (IEEE 802.3u-compliant) on all ports Store-and-forward switching method Jumbo frames of 12K bytes without frame loss ...
-
Page 14: Components
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Components This section describes the components of the GS910/XST series switches. Front Panels The components of the front panels are shown in Figure 2, Figure 3, and Figure 4. -
Page 15: Back Panel
Chapter 1: Product Description Back Panel The GS910/XST series switch has an internal power supply with a single AC power supply socket on the rear panel. Figure 6 shows the rear panel of the GS910/10XST switch. The rear panel for the GS910/18XST and GS910/26XST is as shown in Figure 6. -
Page 16: 100Base-Tx, 1G/2.5G/5G/10G Base-T Twisted Pair Ports
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Duplex Mode Each twisted pair port on the switch can operate in either half- or full-duplex mode. The twisted pair ports are IEEE 802.3u-compliant and automatically negotiate the duplex mode setting. -
Page 17: Sfp/Sfp+ Slot
Chapter 1: Product Description Speed Port 9 on the GS910/10XST switch, port 17 on the GS910/18XST switch, and port 25 on the GS910/26XST switch are capable of 100Mbps, 1Gbps, 2.5Gbps, 5Gbps, and 10Gbps speeds. The ports are IEEE802.3u Auto-Negotiation compliant. With Auto-Negotiation, the switches automatically match the highest possible common speed between the switch port and its end-node. - Page 18 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Table 3. Supported SFP Transceivers (Continued) Supported Model Maximum Operating Temperature AT-SPZX80 70° C (158° F) AT-SP10BD10/I-12 85° C (185° F) AT-SP10BD10/I-13 85° C (185° F) AT-SP10BD40/I-12 85° C (185° F) AT-SP10BD40/I-13 85°...
-
Page 19: Leds
Chapter 1: Product Description LEDs The switch has LEDs to display status information on the switch and ports. Switch LEDs The LEDs on the front panel of the switch display status information. See Figure 7. Figure 7. Switch LEDs Table 4 describes the switch LEDs. Table 4. - Page 20 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Link/Activity Duplex/Loop Duplex/Loop Link/Activity Figure 8. LEDs on 10/100/1000Mbps Ports Table 5 describes the switch LEDs. Table 5. 10/100/1000Mbps Port LEDs State Description Link/Activity Green The port has established a link to a network device at 1Gbps speed.
- Page 21 Chapter 1: Product Description LEDs for the 100M/1G/2.5G/5G/10Gbps Uplink Port The LEDs on port 9 on the GS910/10XST switch, port 17 on the GS910/18XST switch, and port 25 on the GS910/26XST switch display port status. The LED at the left top corner of the port indicates the link/activity;...
-
Page 22: Dip Switches
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide LED for the SFP/SFP+ Uplink Port The LED next to the SFP/SFP+ slot displays link status for port 10 on the GS910/10XST switch, port 18 on the GS910/18XST switch, or port 26 on the GS910/26XST switch. -
Page 23: Power Connector
Chapter 1: Product Description Note Loop Prevention and EEE are only effective on the 10/100/1000Mbps ports. Enabling or disabling these functions using the DIP switches does not affect any operations on the 100M/1G/2.5G/5G/10Gbps and SFP/SFP+ uplink ports. Power Connector The switch has a single AC power supply socket on the back panel. Use the power adapter that came with the switch. -
Page 24: Loop Prevention
The LED of the blocked port starts blinking. Root Switch In a topology with multiple GS910/XST series switches, they elect a root switch when Loop Prevention is enabled on all the switches. Initially, these switches are all root switches. They send Loop Prevention frames and elect the root switch by comparing their switch priorities. -
Page 25: Examples With Multiple Loop Prevention Switches
Chapter 1: Product Description Examples with In examples shown in Figure 12, multiple GS910/XST series switches form links and all switches are Loop Prevention enabled. Switch C has a Multiple Loop lower MAC address than Switch A and Switch B; Switch B has a lower Prevention MAC address than Switch A. -
Page 26: Examples With Loop Prevention And Regular Switches
Figure 13. GS910/XST Series and Regular Switches for Loop Prevention - Case 1 and Case 2 In an example shown in Figure 14, the GS910/XST series switch and a regular switch form a link. The regular switch is causing a loop. When receiving a Loop Prevention frame, the GS910/XST series switch blocks its port. -
Page 27: Examples Within A Loop Prevention Switch
Chapter 1: Product Description Examples within In examples shown in Figure 15, the ports of the GS910/XST series switch are connected. When Loop Prevention is enabled, the switch blocks the a Loop port with the higher port number than the link partner port. -
Page 28: Energy Efficiency Ethernet (Eee)
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Energy Efficiency Ethernet (EEE) The GS910/XST series switches support IEEE 802.3az Energy Efficiency Ethernet (EEE) when the twisted pair ports are operating at a speed of 100Mbps or 1000Mbps. When EEE is enabled on the switch, the power consumption to keep links at a these speeds is reduced during periods of low data activity. -
Page 29: Ethernet Switching Basics
The twisted pair ports on the GS910/XST series switch can operate in half- or full-duplex mode for 10/100 Mbps. They are IEEE 802.3u-compliant and use Auto-Negotiation to set the duplex mode setting for you automatically. - Page 30 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide How a switch signals an end-node to stop transmitting data differs depending on the duplex mode of the end-node and switch port. A twisted pair port operating in half-duplex mode stops an end-node from transmitting data by forcing a collision.
-
Page 31: Chapter 2: Installation
Chapter 2 Installation This chapter contains the following sections: “Reviewing Safety Precautions” on page 32 “Selecting a Site for the Switch” on page 34 “Unpacking the Switch” on page 36 “Installing the Switch on a Table or Desktop” on page 37 ... -
Page 32: Reviewing Safety Precautions
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Reviewing Safety Precautions Review the following safety precautions before you begin to install the switch. Note Important: The indicates that translations of the safety statement are available in the PDF document Translated Safety Statements posted on the Allied Telesis website at alliedtelesis.com/support. - Page 33 Chapter 2: Installation Warning Operating Temperature. This product is designed for a maximum ambient temperature of 50 degrees C. Note All Countries: Install product in accordance with local and National Electrical Codes. Warning An insecurely attached device on a wall may fall and the falling device may lead to damaging itself or causing injuries.
-
Page 34: Selecting A Site For The Switch
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Selecting a Site for the Switch Observe the following requirements when choosing a site for the GS910/XST series switch: If you plan to install the switch on a table, make sure that the table ... - Page 35 Chapter 2: Installation Note The twisted pair ports on the switch feature Auto-MDI when operating at either 10 or 100 Mbps. Each port is individually configured as MDI or MDI-X when connected to an end-node. Consequently, you can use a straight-through twisted pair cable when connecting any network device to a twisted pair port on the switch.
-
Page 36: Unpacking The Switch
Table 9 shows a list of the components. Table 9. Contents in the Shipping Box Item Image One GS910/XST GS910/10XST Switch series switch GS910/18XST Switch GS910/26XST Switch One AC power cord 4. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. -
Page 37: Installing The Switch On A Table Or Desktop
Chapter 2: Installation Installing the Switch on a Table or Desktop Before installing the GS910/XST series switch on a table or desktop, review the guidelines. Guidelines for Here are guidelines for installing the switch on a table or desktop: Installing the The GS910/XST series switch must be installed on a table or ... -
Page 38: Installing The Switch Flat On A Table Or Desktop
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide The GS910/10XST switch can be installed upright on the flat surface as shown in Figure 19. You must use the STND-03 Stand Kit to install the switch. Figure 19. Vertical Installation Options for the GS910/10XST Switch Note The STND-03 Stand Kit must be purchased separately. -
Page 39: Installing The Switch On A Wall
Chapter 2: Installation Installing the Switch on a Wall The GS910/XST series switch can be mounted on a wall using a wall-mount bracket kit. Note To install the GS910/XST series switch on a wall, you must purchase a wall-mount bracket kit separately. - Page 40 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide The GS910/XST series switch must be mounted with the bottom of the switch on the wall. The switch must be installed either horizontally or vertically in one ...
-
Page 41: Installing The Switch In An Equipment Rack
Chapter 2: Installation Installing the Switch in an Equipment Rack The GS910/XST series switch can be mounted on a 19-inch equipment rack using a rack-mount kit. Note To install the GS910/XST series switch, you must purchase a rack mount kit separately. -
Page 42: Cabling Twisted Pair Ports
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Cabling Twisted Pair Ports After installing the GS910/XST series switch, connect twisted pair cables or/and an SFP transceiver to the ports on the switch. To install an SFP transceiver, see “Installing an SFP Transceiver” on page 43. -
Page 43: Installing An Sfp Transceiver
Chapter 2: Installation Installing an SFP Transceiver Before installing an SFP transceiver in the switch, review the following guidelines. Guidelines to Here is a list of guidelines to installing an SFP transceiver: Handling SFP The switch supports 1G and 10G speed on the SFP/SFP+ slot. ... - Page 44 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Figure 21. Installing an SFP Transceiver 3. Verify the position of the handle of the transceiver. The handle should be in the upright position as shown in Figure 22.
- Page 45 Chapter 2: Installation Figure 23. Connecting a Fiber Optic Cable to the SFP Transceiver...
-
Page 46: Powering On The Switch
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Powering On the Switch To power on the switch, perform the following procedure: 1. Before powering on the switch, review the information in “Power Specifications” on page 79. Warning Power cord is used as a disconnection device. -
Page 47: Chapter 3: Wall Installation Using The Brkt-J22 Kit
Chapter 3 Wall Installation Using the BRKT-J22 This chapter explains the procedures how to install a switch on a wall using the BRKT-J22 wall mount kit. It contains the following sections: “Unpacking the BRKT-J22 Wall Mount Kit” on page 48 ... -
Page 48: Unpacking The Brkt-J22 Wall Mount Kit
2. Verify that four brackets are included in your wall mount package listed in Table 12. Table 12. Components in the BRKT-J22 Wall Mount Kit Components Four brackets 3. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. -
Page 49: Installing A Switch Using The Brkt-J22 Wall Mount Kit
Chapter 3: Wall Installation Using the BRKT-J22 Kit Installing a Switch Using the BRKT-J22 Wall Mount Kit This section shows you steps to install a switch on a wall using the BRKT-J22 kit. What to Prepare Before installing a switch on a wall, make sure that the following items are ready. - Page 50 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide 3. Have another person hold the switch with the brackets at the location where the switch is to be installed, while use a pencil to mark the wall at the locations of the four holes in the brackets. See Figure 25.
- Page 51 Chapter 3: Wall Installation Using the BRKT-J22 Kit 7. Make sure that the two brackets are installed securely. 8. Slide the switch into the brackets on the wall as shown in Figure 27. Figure 27. Placing the Switch into the Brackets...
- Page 52 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide 9. Position the two brackets on top of the switch and use a pencil to mark the wall with the locations of the four holes in the brackets. See Figure 28.
- Page 53 Chapter 3: Wall Installation Using the BRKT-J22 Kit 13. Place the two brackets back on the top of the switch and drive screws through the holes to attach the brackets on the wall. See Figure 29. Figure 29. Securing the Top Brackets to the Wall 14.
-
Page 54: Installing A Switch Facing Up
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Installing a To install the switch on a wall with the front panel facing up, install the brackets to support the switch from the sides as shown in Figure 30. - Page 55 Chapter 3: Wall Installation Using the BRKT-J22 Kit 6. Position two brackets on the wall and drive screws through the holes to attach the brackets on the wall. 7. Make sure that the two brackets are installed securely. 8. Slide the switch into the brackets on the wall. 9.
- Page 56 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide...
-
Page 57: Chapter 4: Wall Installation Using The Brkt-J24 Kit
Chapter 4 Wall Installation Using the BRKT-J24 This chapter contains the follows sections: “Unpacking the BRKT-J24 Wall Mount Kit” on page 58 “Installing the Switch on a Wall Using the BRKT-J24 Brackets” on page 59... -
Page 58: Unpacking The Brkt-J24 Wall Mount Kit
2. Verify that One pair of brackets is included in your wall mount package listed in Table 13. Table 13. Components in the BRKT-J24 Wall Mount Kit Components Four brackets 16 M4x6mm screws 3. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. -
Page 59: Installing The Switch On A Wall Using The Brkt-J24 Brackets
Chapter 4: Wall Installation Using the BRKT-J24 Kit Installing the Switch on a Wall Using the BRKT-J24 Brackets The switch can be mounted on a wall using the BRKT-J24 wall mount bracket kit. What to Prepare You need the following items to install the switch on a wall: for Wall Four BRKT-J24 brackets ... - Page 60 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Figure 31. Attaching the Wall Brackets 4. While another person holds the switch at the wall location, mark the holes with a pencil. 5. Pre-drill the marked holes. 6. While another person holds the switch at the wall location, secure the switch to the wall using the eight wall mounting screws.
- Page 61 Chapter 4: Wall Installation Using the BRKT-J24 Kit Figure 32. Installing the Switch on the Wall...
- Page 62 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide...
-
Page 63: Chapter 5: Rack Installation Using The Rkmt-J09 Kit
Chapter 5 Rack Installation Using the RKMT-J09 This chapter explains the procedures how to install a switch in a 19-inch equipment rack using the RKMT-J09 rack mount kit. It contains the following sections: “Unpacking the RKMT-J09 Rack Mount Kit” on page 64 ... -
Page 64: Unpacking The Rkmt-J09 Rack Mount Kit
2. Verify that all hardware components are included in your rack mount package listed in Table 14. Table 14. Components in the RKMT-J09 Rack Mount Kit Components Two Brackets Two Handles Eight M3x6mm screws 3. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. -
Page 65: Installing A Switch Using The Rkmt-J09 Rack Mount Kit
Chapter 5: Rack Installation Using the RKMT-J09 Kit Installing a Switch Using the RKMT-J09 Rack Mount Kit This section shows you steps to install a switch in an equipment rack using the RKMT-J09 kit. What to Prepare Before installing a switch to an equipment rack, make sure that the following items are ready. - Page 66 GS910/XST Series 10 Gibami Ehternet Unmanaged Switch Installation and User’s Guide Figure 34. Attaching the Plates to the Switch 5. Mount the switch in a standard 19-inch equipment rack with four equipment rack screws as shown in Figure 35. Note The equipment rack screws are not included in the RKMT-J09 rack mount kit.
-
Page 67: Chapter 6: Rack Installation Using The Rkmt-J14 Kit
Chapter 6 Rack Installation Using the RKMT-J14 This chapter contains the follows sections: “Unpacking the RKMT-J14 Rack Mount Kit” on page 68 “Installing a Switch Using the RKMT-J14 Rack Mount Kit” on page 69 ... -
Page 68: Unpacking The Rkmt-J14 Rack Mount Kit
Table 15. Table 15. Components in the RKMT-J14 Rack Mount Kit Components Two Brackets Two Handles Four M3x6mm screws for handles Eight M4x6mm screws 3. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. -
Page 69: Installing A Switch Using The Rkmt-J14 Rack Mount Kit
Chapter 6: Rack Installation Using the RKMT-J14 Kit Installing a Switch Using the RKMT-J14 Rack Mount Kit This section shows you steps to install a switch in an equipment rack using the RKMT-J14 kit. What to Prepare Before installing a switch to an equipment rack, make sure that the following items are ready. - Page 70 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide 4. Attach the two rack mount brackets to the sides of the switch with the eight bracket screws as shown in Figure 37. Figure 37. Installing the Brackets on the Switch 5.
-
Page 71: Chapter 7: Rack Installation Using The Rkmt-J15 Kit
Chapter 7 Rack Installation Using the RKMT-J15 This chapter contains the follows sections: “Unpacking the RKMT-J15 Rack Mount Kit” on page 72 “Installing Two Switches in a Row of the Equipment Rack” on page 73 ... -
Page 72: Unpacking The Rkmt-J15 Rack Mount Kit
2. Verify that One pair of brackets is included in your wall mount package listed in Table 16. Table 16. Components in the RKMT-J15 Rack Mount Kit Components Tray Four M4x6mm screws 3. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. -
Page 73: Installing Two Switches In A Row Of The Equipment Rack
Chapter 7: Rack Installation Using the RKMT-J15 Kit Installing Two Switches in a Row of the Equipment Rack This section shows you steps to install two switches on a row of the equipment rack using the RKMT-J15 rack mount kit. What to Prepare Before installing two switches on a row of the equipment rack, make sure that the following items are ready. - Page 74 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide 4. Turn the tray fixing screws on counter clockwise and pull out the tray. See Figure 40. You can draw the tray to a maximum of 250mm from the tray chassis.
- Page 75 Chapter 7: Rack Installation Using the RKMT-J15 Kit Figure 41. Placing the Switch in the RKMT-J15 Tray 6. Slide the tray back to its original position and turning the tray fixing screws on clockwise as shown in Figure 42. Figure 42. Securing the RKMT-J15 Tray in an Equipment Rack...
- Page 76 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide...
-
Page 77: Chapter 8: Troubleshooting
If you are still unable to resolve the problem after following the instructions in this chapter, contact Allied Telesis Technical Support for assistance. Refer to “Contacting Allied Telesis” on page 9. Check the POWER LED on the front of the switch. If the LED is OFF,... - Page 78 GS910/XST Series 10 Gigabit Ethernet Unmanaged Switch Installation and User’s Guide...
-
Page 79: Appendix A: Technical Specifications
Appendix A Technical Specifications This appendix contains the following sections: “Physical Specifications” “Power Specifications” on page 79 “Environmental Specifications” “RJ-45 Twisted Pair Port Connectors” on page 81 Physical Specifications Table 17. Physical Specifications Dimensions (W x D x H) Weight 1.9 kg (4.2 lb) GS910/10XST... -
Page 80: Environmental Specifications
GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide Environmental Specifications Table 19. Environmental Specifications Parameter Value Without an SFP 0° C to 50° C (32° F to 122° F) With an SFP with the max operating temperature 85° C 0°... -
Page 81: Rj-45 Twisted Pair Port Connectors
Appendix A: Technical Specifications RJ-45 Twisted Pair Port Connectors This section lists the connectors and connector pinouts for the GS910 series switch and its components. Figure 43 illustrates the pin layout to an RJ-45 connector and port. Figure 43. RJ-45 Connector and Port Pin Layout Table 20 lists the RJ-45 pin signals when a twisted pair port is operating in the MDI configuration. - Page 82 GS910/XST Series 10 Gigabit Ehternet Unmanaged Switch Installation and User’s Guide...