Connecting A Dvd Player (Dvd); Connecting A Video Cassette Recorder (Video 1) - Onkyo TX-NR801 Instruction Manual

Connecting to Audio/Video Equipment—Continued
For other models:
Note that the OSD Menu data will be output to the
MONITOR OUT VIDEO, S VIDEO and
COMPONENT VIDEO jacks. When you connect any
OSD-specific monitor TV to the VIDEO connectors, you
can disable the OSD output to COMPONENT VIDEO
OUTPUT. To disable the OSD output, select Setup
Menu → Preference → OSD Setup → Component
Video, and then select "OSD Off" (See page 63).

Connecting a DVD Player (DVD)

DIGITAL PRE OUT
AUDIO VIDEO
IN R L ANTENNA
COAX FRONT
1
SUB CENTER
AM
2 OUT
R L
SURR
3 IN
SURR
R L
BACK/
OPT
ZONE 2
FM
1 OUT
75
FRONT
MULTI CH
2 IN
INPUT
AUDIO
R L
R L
SUB CENTER
3 PHONO OUT
IN
DIGITAL AUDIO VIDEO S VIDEO
SURR
CD IN
DIGITAL
IN
OUT IN
R L
OPT OUT
1 IN
COAX R L
SURR
BACK
TAPE
2 IN
IN IN DVD
1 GND
R L R L
AUDIO AUDIO VIDEO
R L
DIGITAL
OUT AUDIO VIDEO S VIDEO
COAX OUT OUT
DVD player
Using an RCA video connection cable, connect the
video output jack (composite) of the DVD or LD player
to the DVD VIDEO IN jack of the TX-NR801/
TX-NR801E. Or if the DVD or LD player has an S video
output jack, connect it to the DVD S VIDEO IN jack
with an S video connection cable. Or if the device has
component video outputs, connect them to one of the
banks of COMPONENT VIDEO INPUT jacks on the
TX-NR801/TX-NR801E.
On the initial settings of the TX-NR801/TX-NR801E,
the DVD input source is set for the COMPONENT
VIDEO INPUT 1 jacks.
If you connect the DVD or LD player to the
COMPONENT VIDEO INPUT 2 jacks, this must be
changed at Setup Menu → Input Setup → Video Setup
→ Component Video (See page 38).
Using an RCA audio connection cable, connect the
audio output jacks of the DVD or LD player to the DVD
AUDIO IN jacks of the TX-NR801/TX-NR801E. Make
sure that you properly connect the left channel to the L
jack and the right channel to the R jack.
If the device has a digital output, connect it to either the
DIGITAL IN COAX jack or DIGITAL IN OPT jack of
the TX-NR801/TX-NR801E, depending on the type of
connector on the DVD player.
On the initial settings of the TX-NR801/TX-NR801E, the
DVD input source is set for digital input at the COAX 1 jack.
COMPONENT
COMPONENT
S VIDEO
VIDEO
VIDEO
MONITOR OUTPUT
OUT Y
INPUT 1
ZONE 2 P B
Y
DVD P
R
INPUT 1
Y
VIDEO 1
P
B
P
B
P
R
VIDEO 2
INPUT 2
Y
P
R
VIDEO 3 P B
VIDEO 4 P
R
S VIDEO
OUT
Y P P
B R
COMPONENT
VIDEO
OUTPUT
If the digital connection is made at a different jack, this
must be changed at Setup Menu → Input Setup →
Digital Setup (See page 36).
Make sure of your DVD player's digital output settings.
You need to access the On Screen Menu of your DVD
player. See the owner's Manual on your DVD player.
Also, you need to aware of the Table of contents for the
movie, selecting the movie for Dolby Digital or DTS,
depends how the movie is encoded.
Connecting a Video Cassette
Recorder (VIDEO 1)
DIGITAL PRE OUT
AUDIO
IN R L ANTENNA
COAX FRONT
1
SUB CENTER
AM
2
R L
SURR
3
SURR
R L
BACK/
OPT
ZONE 2
FM
1
75
FRONT
MULTI CH
2
INPUT
AUDIO
R L
R L
SUB CENTER
3 PHONO
IN
AUDIO
SURR
CD
DIGITAL
IN
OUT R L
R L
OPT OUT
1
SURR
BACK
TAPE
OUT
2
IN
GND
R L R L
AUDIO AUDIO
IN
R L
VIDEO S VIDEO
AUDIO IN IN IN
Using RCA video connection cables, connect the video
output jack (composite) of the video cassette recorder to the
VIDEO 1 VIDEO IN jack of the TX-NR801/TX-NR801E
and connect the video input jack of the video cassette
recorder to the VIDEO 1 VIDEO OUT jack of the
TX-NR801/TX-NR801E. Or if the video cassette recorder
has S video input and output jacks, connect them to the
VIDEO 1 S VIDEO IN and OUT jacks of the TX-NR801/
TX-NR801E using S video connection cables. Or if the
video cassette recorder has component video outputs,
connect them to one of the banks of COMPONENT
VIDEO INPUT jacks on the TX-NR801/TX-NR801E.
On the initial settings of the TX-NR801/TX-NR801E,
the VIDEO 1 input source is set for the
COMPONENT VIDEO INPUT 2 jacks.
If you connect the video cassette recorder to the COMPONENT
VIDEO INPUT 1 jacks, this must be changed at Setup Menu →
Input Setup → Video Setup → Component Video (See page 38).
Using RCA audio connection cables, connect the audio
output jacks of the video cassette recorder to the VIDEO 1
AUDIO IN jacks of the TX-NR801/TX-NR801E and
connect the audio input jacks of the video cassette recorder to
the VIDEO 1 AUDIO OUT jacks of the TX-NR801/
TX-NR801E. Make sure that you properly connect the left
channels to the L jacks and the right channels to the R jacks.
COMPONENT
VIDEO S VIDEO
VIDEO
MONITOR OUTPUT
OUT
Y
OUT ZONE 2 P
B
DVD
IN P R
INPUT 1
OUT Y
VIDEO 1
P
IN B
OUT P
R
VIDEO 2
VIDEO S VIDEO
INPUT 2
Y
IN
IN VIDEO 3 P B
VIDEO 4
IN P R
VIDEO 1
VIDEO S VIDEO
R L
VIDEO S VIDEO
AUDIO OUT OUT OUT
VCR
21