Onkyo TX-NR1008 Firmware Update
Hide thumbs
Also See for TX-NR1008:
- Instruction manual (104 pages) ,
- Specifications (2 pages) ,
- Quick setup (2 pages)
Advertisement
Firmware Update for TX-NR708/808/1008 and
HT-RC270
There are the following methods to update the firmware: via network and via USB storage.
Please choose either one that suits your condition. Before you start, carefully read the
Update Procedure. It will take about 30 minutes to update the firmware.
■Update via network
You need a wired Internet connection to update the firmware.
For the update procedure, please refer to
■Update via USB storage
Please prepare a USB storage device such as a USB flash memory stick. You need at
least 32 MB of available space to update the firmware.
For the update procedure, please refer to
Precautions:
• Check the network connection before update.
• Do not touch the cable or any other device connected to the AV receiver during updating process.
• Do not access the AV receiver from PC during updating process.
• Do not shutdown the power of the AV receiver while update.
• The storage media in the USB card reader may not work.
• If the storage device has been partitioned, each section will be treated as an independent device.
• If the USB mass storage device contains a lot of data, the AV receiver may take a while to read it.
• Operation with all USB mass storage devices including the ability to power them is not guaranteed.
• Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB mass
storage device when that device is used with the AV receiver. Onkyo recommends that you back
up your important music files beforehand.
• If you connect a USB hard disk drive to the USB port, Onkyo recommends that you use its AC
adapter to power it.
• USB hubs and USB devices with hub functions are not supported. Do not connect your USB mass
storage device via a USB hub.
• USB mass storage devices with security functions are not supported.
Limitation of liability
The program and accompanying online documentation are furnished to you for use at your own
risk. Onkyo will not be liable and you will have no remedy for damages for any claim of any kind
whatsoever concerning your use of the program or the accompanying online documentation,
regardless of legal theory, and whether arising in tort or contract. In no event will Onkyo be liable
to you or any third party for any special, indirect, incidental, or consequential damages of any kind,
including, but not limited to, compensation, reimbursement or damages on account of the loss of
present or prospective profits, loss of data, or for any other reason whatsoever.
2).
(➔
(➔
5).
En
1
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Onkyo TX-NR1008
Summary of Contents for Onkyo TX-NR1008
- Page 1 AV receiver. Onkyo recommends that you back up your important music files beforehand. • If you connect a USB hard disk drive to the USB port, Onkyo recommends that you use its AC adapter to power it.
-
Page 2: Updating The Firmware Via Network
Updating the Firmware via Network TX-NR708/808/1008 and HT-RC270 allow you to How to turn off RIHD update firmware using network connection on rear In the Main menu select “Hardware Setup”. panel. In this procedure, on-screen display may vary depend- ing on the model. Notes •... - Page 3 ■Update procedure Press RECEIVER followed by SETUP on the Select “Update” and press ENTER. remote controller. Updating will begin. Main menu will be displayed on TV screen. As the updating progresses, the TV screen may Procedures thereafter can also be performed on disappear depending on the program updated.
-
Page 4: Troubleshooting
Case6: Error Code Description If you do not have a wired connection to the net- -10, Ethernet cable is not detected. Con- work, please contact Onkyo Support. nect the cable properly. See the instruction manual for the network connection. -11, -13, Internet connection error. -
Page 5: Updating The Firmware Via Usb
Updating the Firmware via USB TX-NR708/808/1008 and HT-RC270 allow you to How to turn off RIHD update firmware using a USB storage device. In the Main menu select “Hardware Setup”. In this procedure, on-screen display may vary depend- ing on the model. Notes •... - Page 6 Connect a USB storage device to your PC. If there is any data in the USB storage device, remove it. Download the firmware file from the Onkyo web site. The file name is as follows: ONKAVR0003_*******.zip Unzip the downloaded file. The following three files are created: ONKAVR0003_*******.of1...
- Page 7 The firmware file is not found in the root folder of the USB storage device, or the firmware file is for other model. Retry download. If the error persists, please contact Onkyo Support (indi- cated in the last page) and provide the error code. Others Retry the update procedure from the beginning.
- Page 8 Unit 1&12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung, N.T., Hong Kong Tel: 852-2429-3118 Fax: 852-2428-9039 <http://www.onkyochina.com/> Asia, Oceania, Middle East, Africa Please contact an ONKYO distributor referring to Onkyo SUPPORT site. <http://www.intl.onkyo.com/support/local_support/index.html> Y1008-1 SN 29355808 * 2 9 3 5 5 8 0 8 * (C) Copyright 2010 ONKYO CORPORATION Japan.
Need help?
Do you have a question about the TX-NR1008 and is the answer not in the manual?
Questions and answers