Rear Panel - Onkyo TX-NR801 Instruction Manual

Index Parts and Facilities—Continued

Rear Panel

DIGITAL PRE OUT
IN
R L
COAX FRONT
1
SUB CENTER
2
SURR
3
SURR
R L
BACK/
OPT
ZONE 2
1
FRONT
MULTI CH
2
INPUT
R L
SUB
CENTER
3
SURR
DIGITAL
OUT
R L
OPT
1
SURR
BACK
2
GND
For more information regarding connection procedures,
see pages indicated in brackets [ ].
1
DIGITAL IN/OUT [21-24]
These jacks are for connecting components with
digital input and output capabilities. To connect a
CD player, see page 23; to connect an MD or CD
recorder, see page 24; to connect a DAT deck, see
page 24; to connect a DVD player, see page 21; to
connect a DVD recorder, see page 22; and to con-
nect a digital satellite tuner, see page 22.
2
PRE OUT [18, 25, 66]
To use the TX-NR801/TX-NR801E as a preampli-
fier, connect a power amplifier to this jack.
3
ANTENNA [14]
These jacks are for connecting the FM indoor
antenna and the AM loop antenna that are supplied
with the TX-NR801/TX-NR801E.
4
ZONE 2 VIDEO OUT [21, 66]
This jack is for connecting the component that will
be used in the remote zone (Zone 2).
5
MONITOR OUT VIDEO/S VIDEO [20]
These jacks are for connecting to the video input
jacks on television monitors or projectors.
6
COMPONENT VIDEO OUTPUT [20]
These jacks are for connecting to the component
video input jacks on television monitors or projectors.
7
ETHERNET (Net-Tune) [71]
This connector is for connecting to an Ethernet network.
8
SPEAKERS [18, 66]
These terminals are for connecting the speakers.
9
AC OUTLETS [24]
This AC outlet is provided to plug in the power cord
from another component. The shape and number of
the AC outlet depend on the shipping destination.
COMPONENT
AUDIO VIDEO S VIDEO
ANTENNA
MONITOR
OUT
AM
OUT ZONE 2
R L
IN DVD
FM
OUT
75
VIDEO 1
IN
AUDIO
R L
PHONO OUT
IN
VIDEO 2
CD IN
IN
OUT
VIDEO 3
IN
TAPE
IN VIDEO 4
IN
R L R L
AUDIO AUDIO VIDEO S VIDEO
VIDEO
FRONT SPEAKERS
OUTPUT
R L
Y
P
B
P
R
INPUT 1
Y
ETHERNET
( )
Net-Tune
CENTER
P
B
SPEAKER
P
R
CAUTION:
SPEAKER
INPUT 2
IMPEDANCE
Y
4 OHMS MIN. OR
I R
6 OHMS MIN.
/SPEAKER
IN
SEE INSTRUCTION
P
B
MANUAL FOR
CORRECT SETTINGS.
OUT
P
R
0
MULTI CH INPUT [64]
This connector is for connecting components with a
multichannel output.
A
PHONO/CD/TAPE AUDIO IN/OUT [23, 24]
These connectors are for connecting to the audio
input and output jacks on audio components. To
connect a turntable, see page 24; to connect a CD
player, see page 23; and to connect a cassette tape
deck, MD recorder, or CD recorder, see page 24.
B
DVD/VIDEO1-4 IN/OUT [21, 22]
These connectors are for connecting to the video
input and output jacks on video components. To
connect a DVD player, see page 21; to connect a
DVD recorder, see page 22; to connect a VCR, see
page 21; and to connect a digital satellite tuner, see
page 22.
C
COMPONENT VIDEO INPUT1/2 [21, 22]
These connectors are for connecting to the compo-
nent video outputs of video components that have
them. To connect a DVD player, see page 21; to
connect a DVD recorder, see page 22; and to con-
nect a digital satellite tuner, see page 22.
D
IR IN/OUT [69]
These connectors are for connecting the remote sen-
sor of a multi-room kit (sold separately).
E
[26]
This jack is for connecting other Onkyo compo-
nents equipped with the same
audio connection cables must also be connected.
F
VOLTAGE SELECTOR [7] (Worldwide models
only)
This is only available on the worldwide model.
Before connecting the power cord to the wall outlet,
be sure to set this to the correct power supply volt-
age for your region.
SURR SPEAKERS
R L
AC OUTLETS
AC 120 V 60 Hz
SWITCHED
TOTAL 120W 1A MAX.
SURR
BACK/
ZONE 2
SPEAKERS
R L
VOLTAGE
SELECTOR
120V
AV RECEIVER
TX-NR 801
MODEL NO.
220-230V
REMOTE
CONTROL
terminal. The
11