Connecting; Compatible Av Components; Connections For Remote Control - Onkyo TX-NR801 Instruction Manual

Connecting

The terminal on the TX-NR801/TX-NR801E is for
connecting other Onkyo components equipped with the
same terminal. When a component is connected to
the terminal, it can be operated by the remote
controller supplied with the TX-NR801/TX-NR801E. In
addition, when you connect a component to the
terminal, you can also perform the system operations
given below.
Power on/ready function
When the TX-NR801/TX-NR801E is in the standby
state, if an -connected component is turned on, the
TX-NR801/TX-NR801E also turns on and the input
source selected at the TX-NR801/TX-NR801E
automatically switches to that component.
Be aware that this function will not work if the power
cord for the -connected component is connected to
the AC OUTLET on the TX-NR801/TX-NR801E, or if
the TX-NR801/TX-NR801E has already been turned on.
Direct change function
When the play button is pressed on an
component, the input source selected at the TX-NR801/
TX-NR801E automatically changes to that component.
Power off function
When the TX-NR801/TX-NR801E is placed in the
standby state, all
automatically put into the standby state.
Also, if you press the ON button on the TX-NR801/
TX-NR801E remote controller while the TX-NR801/
TX-NR801E is turned on, all
components (DVD players, CD players, MD recorders,
tuners, etc.) are also turned on.
Onkyo DVD player
DIGITAL OUT
OPTICAL
DIGITAL
AUDIO
IN
R
OPT
1
DIGITAL PRE OUT
IN R L ANTENNA
COAX FRONT
1
SUB CENTER
AM
2
SURR
3
SURR
R L
BACK/
OPT
ZONE 2
FM
1
75
FRONT
MULTI CH
2
INPUT
AUDIO
R L
R L
SUB CENTER
3 PHONO
IN
SURR
CD
DIGITAL
IN
OUT
R L
OPT
OUT
1
SURR
BACK
TAPE
2
IN
GND
R L
AUDIO
26

-compatible AV Components

-connected
-connected components are also
-connected
REMOTE
CONTROL
L
R
ANALOG
OUTPUT
REMOTE
L
CONTROL
IN
COMPONENT
AUDIO VIDEO S VIDEO
VIDEO
FRONT SPEAKERS
OUTPUT
MONITOR R
OUT Y
OUT ZONE 2 P
B
R L
IN DVD P R
INPUT 1
OUT Y
ETHERNET
VIDEO 1 ( )
Net-Tune
CENTER
IN P
B
SPEAKER
OUT P R
CAUTION:
SPEAKER
VIDEO 2
INPUT 2
IMPEDANCE
IN Y
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
IN
SEE INSTRUCTION
VIDEO 3 P
IN B
MANUAL FOR
CORRECT SETTINGS.
OUT
IN VIDEO 4 P R
R L
AUDIO VIDEO S VIDEO

Connections for Remote Control (

To connect components using the
connect a remote control cable from this
the terminal of the other component. An
control cable with a 1/8 inch (3.5 mm) miniature two-
conductor plug comes with every cassette tape deck,
compact disc player, MD recorder, and DVD player that
has an
• When performing operations with
components using the
remote zone (Zone 2).
• For remote control operation, the audio connection
cables must also be connected.
• If a component has two
either one to connect to the TX-NR801/TX-NR801E.
The other one can be used to daisy chain with another
component.
• With Onkyo DVD players, you can enter the pre-
program code so that you can operate the DVD player
directly with the remote controller without connecting
the
Ex: Onkyo CD player
Ex: Onkyo cassette tape
deck
Remote
control
cable
SURR SPEAKERS
L R L
R L
I R
MO
REMOTE
CONTROL
terminal.
system, do not use the
terminals, you can use
terminals (See page 82).
REMOTE
CONTROL
connector
connector
Remote control cable
)
terminal, simply
terminal to
remote
-connected
TX-NR801/
TX-NR801E