ESAB THERMAL DINAMICS CUTMASTER 60i Operating Manual page 49

CutMaster® 60i With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Out-
put
Inches mm (Cat. Volts
No.) (VDC)
0.032 0.8 9-8208 116
0.051 1.3 9-8208 116
0.064 1.6 9-8208 118
0.079 2.0 9-8208 116
0.125 3.2 9-8208 130
0.188 4.8 9-8208 132
0.250 6.4 9-8208 134
0.375 9.5 9-8208 143
CutMaster® 60i With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Out-
put
Inches mm (Cat. Volts
No.) (VDC)
0.060 1.5 9-8210 124
0.075 1.9 9-8210 126
0.120 3.0 9-8210 126
0.135 3.4 9-8210 128
0.188 4.8 9-8210 128
0.250 6.4 9-8210 123
0.375 9.5 9-8210 132
0.500 12.7 9-8210 137
0.625 15.9 9-8210 139
0.750 19.1 9-8210 145
1.000 25.4 9-8210 156
0-5561
Amper- Speed (Per
age Minute)
(Amps) Inches Meters Inches mm
40 220 5.59
40 210 5.33
40 180 4.57
40 150 3.81
40 75 1.91
40 60 1.52
40 28 0.71
40 11 0.28
Amper- Speed (Per
age Minute)
(Amps) Inches Meters Inches mm
60 250 6.35 0.19 4.8
60 237 6.02 0.19 4.8
60 230 5.84 0.19 4.8
60 142 3.61 0.19 4.8
60 125 3.18 0.19 4.8
60 80 2.03 0.19 4.8
60 34 0.86 0.19 4.8
60 23 0.58 0.19 4.8
60 14 0.36 0.19 4.8
60 14 0.36 0.19 4.8
60 4 0.10 0.19 4.8
OPERATION
Type Material: Aluminum
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas
Pressure*
psi bar
0.187 4.8
0.187 4.8
0.187 4.8
0.19 4.8
0.19 4.8
0.187 4.8
0.187 4.8
0.187 4.8
Type Material: Mild Steel
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas
Pressure*
psi bar
CUTMASTER 60i
Flow (SCFH) Pierce Pierce Height
Plasma Total** Delay Inches mm
(Sec)
55 170 0.00 0.2
55 170 0.00 0.2
55 170 0.10 0.2
55 170 0.30 0.2
55 170 0.40 0.2
55 170 0.60 0.2
55 170 1.00 0.2
55 170 NR NR
Flow (SCFH) Pierce Pierce Height
Plasma Total** Delay Inches mm
(Sec)
90 245 0.00 0.2
90 245 0.10 0.2
90 245 0.10 0.2
90 245 0.10 0.2
90 245 0.20 0.2
90 245 0.30 0.2
90 245 0.50 0.2
90 245 0.75 0.2
90 245 NR NR
90 245 NR NR
90 245 NR NR
5.1
5.1
5.1
5.1
5.1
5.1
5.1
NR
5.1
5.1
5.1
5.1
5.1
5.1
5.1
5.1
NR
NR
NR
49