Device Description - WAGO -I/O-SYSTEM 750 Manual

WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Pos : 19 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/Gerätebeschr eibung - Übersc hrift 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1
3

Device Description

Pos : 20.1 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/Anwendung/D O/Anwendung 750- x5xx D O @ 3\mod_1233764594468_21.doc x @ 27120 @ @ 1
The 750-531 (4DO 24V DC 0.5A/ 2-conductor) Digital Output Module transmits
binary control signals from the automation device to the connected actuators (e.g.,
solenoid valves, contactors, transmitters, relays or other electrical loads).
Pos : 20.2 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DO/I/O-Besc hrei bung 750-05xx 4 D O 2-Leiter (DO und 0 V) @ 5\mod_1246611623218_21.doc x @ 36565 @ @ 1
The module has four output channels. Four 2-conductor actuators may be directly
connected to the module.
The actuators can be connected using connection DO 1 or DO 2, DO 3, DO 4 and
0 V.
Pos : 20.3 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/Allgemei n/Ver weis auf Kapitel "Ansc hlüss e" @ 8\mod_1276775378035_21.doc x @ 57956 @ @ 1
The assignment of the connections is described in the "Connectors" section.
Pos : 20.4 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/Allgemei n/Ver weis auf Kapitel "Geräte anschli eß en" > "Ansc hlus sbeis piel(e)" @ 5\mod_1246015203281_21.doc x @ 36298 @ @ 1
Connection examples are shown in section "Connecting Devices" > ... >
"Connection Example(s)".
Pos : 20.5 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits hinweis e/HinweisHi nweis : DO Potential ver viel fältigungs module für Aktor versorgung eins etz en @ 3\mod_1233765481250_21.doc x @ 27140 @ @ 1
Use field side connection modules!
Where required, use the appropriate field side connection modules for power
supply to the actuators.
Pos : 20.6 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/AchtungAc htung: DO Indukti onsspannungsbegrenz ung El ektr oni k @ 3\mod_1233815757507_21.doc x @ 27153 @ @ 1
Limit all induced voltage!
The electronic components of the I/O module can be damaged by the induced
voltage produced when inductive loads are de-activated.
An appropriate protection circuit, e.g., a recovery diode, must be installed in
parallel to the load to limit this induced voltage.
Pos : 20.7 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DO/I/O-Besc hrei bung 750-05xx DO kurzsc hl ussfest @ 3\mod_1233817429086_21.doc x @ 27167 @ @ 1
The output channels are electrically short-circuit-protected.
Pos : 20.8 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DO/I/O-Besc hrei bung 750- x5xx D O HSS / posi ti vsc haltend (24 V) @ 3\mod_1233816955742_21.doc x @ 27160 @ @ 1
The I/O module outputs provide high-side switching. If the signal status of an
output channel is at "high" the 24 V potential for field power will be switched to
the appropriate output connection.
Pos : 20.9 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DO/I/O-Besc hrei bung 750-05xx Leistungs kontakt durch Ei nspeis eklemme @ 5\mod_1246856959993_21.doc x @ 36590 @ @ 1
The supply voltage for the field side is derived from an adjacent supply module by
means of power jumper contacts.
Pos : 20.10 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Ac htungAc htung: D O Ü berlasts chutz - Ei npeis eklemme mit Sic her ung @ 3\mod_1233814881117_21.doc x @ 27150 @ @ 1
Provide for overload protection!
Overloading can damage the electronic components of the I/O module.
A fused supply module (750-601) must be installed upstream of the I/O module to
protect it against overloading!
Pos : 20.11 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ei nleitung/LED-Anzeig e/LED Z us tand Signal @ 3\mod_1233755258578_21.doc x @ 27087 @ @ 1
A green LED indicates the switched status of each channel.
Pos : 20.12 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ei nleitung/LED-Anzeig e/Ver weis auf Kapitel " Anzeig eel emente" @ 5\mod_1246010525000_21.doc x @ 36194 @ @ 1
The meaning of the LEDs is described in the "Display Elements" section.
Pos : 20.13 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ei nleitung/Versorgung/Vers orgung 24 V, 0 V über Leistungs kontakte Standard @ 3\mod_1226498974531_21.doc x @ 25020 @ @ 1
Manual
Version 1.3.0
Device Description 13