Device Description - WAGO I/O-SYSTEM 750 XTR Manual

WAGO-I/O-SYSTEM 750 XTR
750-407/040-000 2DI 220V DC 3.0ms /XTR
3

Device Description

Pos : 18.1 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/Anwendung/DI/Anwendung 750- x4xx D I @ 3\mod_1233762736718_21.doc x @ 27108 @ @ 1
The digital input module 750-407/040-000 (2DI 220V DC 3.0ms /XTR) receives
control signals from digital field (e.g. of sensors, transmitters, switches or
proximity switches).
Pos : 18.2 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DI/I/O-Besc hrei bung 750-0407 2 D I 2-/3-/4-Leiter (DI, 220 V, 0 V und Erde) @ 7\mod_1274862216081_21.doc x @ 57033 @ @ 1
The I/O module has 2 input channels, providing a direct connection to 2-, 3- or 4-
wire sensors.
The sensors are connected to the following CAGE CLAMP
220 V, 0 V and ground, or DI 2, 220 V, 0 V and ground.
Pos : 18.3 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/Allgemei n/Ver weis auf Kapitel "Ansc hlüss e" @ 8\mod_1276775378035_21.doc x @ 57956 @ @ 1
The assignment of the connections is described in the "Connectors" section.
Pos : 18.4 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/Allgemei n/Ver weis auf Kapitel "Geräte anschli eß en" > "Ansc hlus sbeis piel(e)" @ 5\mod_1246015203281_21.doc x @ 36298 @ @ 1
Connection examples are shown in section "Connecting Devices" > ... >
"Connection Example(s)".
Pos : 18.5 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DI/I/O-Besc hrei bung 750- x4xx DI RC-Filter 3,0 ms @ 3\mod_1233755071062_21.doc x @ 27080 @ @ 1
Each input channel has a RC noise rejection filter with a time constant of 3.0 ms.
Pos : 18.6 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/LED-Anz eige/LED Zustand Signal @ 3\mod_1233755258578_21.doc x @ 27087 @ @ 1
A green LED indicates the switched status of each channel.
Pos : 18.7 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/LED-Anz eige/Ver weis auf Kapitel "Anz eigeelemente" @ 5\mod_1246010525000_21.doc x @ 36194 @ @ 1
The meaning of the LEDs is described in the "Display Elements" section.
Pos : 18.8 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: Eins peisekl emme für Vers orgung ungleich 24 V eins etzen @ 5\mod_1247032609340_21.doc x @ 36784 @ @ 1
Only connect to I/O modules with the same field power supply!
The I/O module 750-407/040-000 requires a field supply not equal to 24 VDC.
Therefore, this I/O module 750-407/040-000 shall only be connected to modules
having the same field power supply.
If using an adjacent I/O module designed for another field power supply, place an
appropriate supply module between this adjacent module and the I/O module 750-
407/040-000.
Failure to observe these instructions may result in damage to properties or injuries
to people.
Pos : 18.9 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/Vers orgung/Vers orgung DC 220 V, 0 V über Leis tungs kontakte (XTR) @ 24\mod_1447317072205_21.doc x @ 195498 @ @ 1
Use a 750-612/040-000 power supply!
For 220 VDC power on the field level, an additional 750-612/040-000 supply
module must be positioned before a terminal block 750-407/040-000 or before
I/O modules 750-407/040-000 arranged in blocks!
The I/O module receives the 220 VDC potential and the 0 V potential for the field
level from an upstream I/O module via the power contacts used as blade contacts.
It then provides this potential to subsequent I/O modules via the power contacts
used as spring contacts.
Pos : 18.10 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Ac htung/Ac htung: Maxi maler Str om Eins peisung 750-0407/040- 000 @ 17\mod_1382014146271_21.doc x @ 134451 @ @ 1
Manual
Version 1.2.0
Device Description
®
connectors: DI 1,
13