Xilinx Zynq UltraScale+ RFSoC ZCU208 User Manual page 31

Table 3: Command List (cont'd)
Command
SetThresholdSettings
SetSignalDetector
SetupFIFO
SetupFIFOObs
Shutdown
StartUp
CustomStartup
UpdateEvent
DynamicPLLConfig
MultiBand
SetCalCoefficients
GetCalCoefficients
DisableCoefficientsOverride
SetDACCompMode
GetEnabledInterrupts
SetDACDataScaler
GetDACDataScaler
GetExtPllConfig
GetExtParentClkList
GetExtParentClkConfig
GetExtPllFreqList
RfclkReadReg
RfclkWriteReg
SetExtParentclk
SetExtPllClkRate
UG1433 (v1.2) October 27, 2021
RF Data Converter Evaluation Tool User Guide
Input Parameters
Tile, Block,
ThresholdSettings.UpdateThreshold,
ThresholdSettings.ThresholdMode[0],
ThresholdSettings.ThresholdMode[1],
ThresholdSettings.ThresholdAvgVal[0],
ThresholdSettings.ThresholdAvgVal[1],
None
ThresholdSettings.ThresholdUnderVal[
0],
ThresholdSettings.ThresholdUnderVal[
1],
ThresholdSettings.ThresholdOverVal[0],
ThresholdSettings.ThresholdOverVal[1]
Tile, Block, Mode, TimeConstant, Flush,
EnableIntegrator, Threshold,
Tile, Block
ThreshOnTriggerCnt,
ThreshOffTriggerCnt, HysteresisEnable
Type, Tile, Enable None
Type, Tile, Enable None
Type, Tile None
Type, Tile None
Type, Tile, StartState, EndState None
Type, Tile, Block, Event None
Type, Tile, Source, RefClkFreq,
RefClkDivider, FeedbackDivider, OutputDivider
SamplingRate
Type, Tile, DigitalDataPathMask,
Type, Tile, DigitalDataPathMask, DataType, DataConverterMask
DataType, DataConverterMask
Tile, Block, CalBlock, Coeffs.Coeff0,
Coeffs.Coeff1, Coeffs.Coeff2,
Coeffs.Coeff3, Coeffs.Coeff4, None
Coeffs.Coeff5, Coeffs.Coeff6,
Coeffs.Coeff7
Tile, Block, CalBlock, Coeffs.Coeff0, Coeffs.Coeff1, Coeffs.Coeff2, Coeffs.Coeff3,
Tile, Block, CalBlock
Coeffs.Coeff4, Coeffs.Coeff5, Coeffs.Coeff6, Coeffs.Coeff7
Tile, Block, CalBlock None
Tile, Block, Enable Tile, Block, Enable
Type, Tile, Block Type, Tile, Block, IntrMask
Tile, Block, Enabled None
Tile, Block Tile, Block, Enabled
Board Control Commands
Board_id, Pll_src Freq
Board_id LMK_FREQ_LIST[LMK_FREQ_NUM]
Board_id LMKCurrentFreq
ADC_FREQ_LIST[LMX_ADC_NUM] or DAC_FREQ_LIST[LMX_DAC_NUM]
Board_id, Pll_src
depending on Pll_Src
Board_id, chip_id, reg_addr Board_id, chip_id, reg_addr, data
Board_id, chip_id, reg_addr, data Board_id, chip_id, reg_addr, data
Board_id, freq Board_id, freq
Board_id, Pll_src, freq Board_id, Pll_Src, freq
Appendix B: Command List
Output Parameters
Send Feedback
Description
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Cf. PG269
Return the current
frequency of the LMX.
Return a list of
frequencies available
for the LMK.
Return the current
LMK frequency.
Return a list of
allowed values for the
LMX.
Read a register from
the LMK/LMX.
Write a register from
the LMK/LMX with the
following parameters:
Board_id (always 0)
chip_id ( 0 :PLL ADC, 1
PLL DAC, 2: LMK)
reg_addr (register
address from the TCS
file)
data (data from the
TCS file)
Configure LMK clock
with requested
frequency.
Configure PLL (LMX)
with requested
frequency.
www.xilinx.com
31