071: Limit-Cho/Fl (Limiter - Chorus/Flanger); 072: Limit-Phaser - Korg Triton-Rack Parameter Manual

071: Limit–Cho/Fl
(Limiter – Chorus/Flanger)
This effect combines a mono-type limiter and a chorus/
flanger. You can change the order of the effect connection.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Limiter
+
Limiter
EQ Trim
Gain Adjust
Right
Envelope - Control
[LMT] Ratio
a
Sets the signal compression ratio
Threshld (Threshold)
Sets the level above which the compressor is applied
b
G.Adj (Gain Adjust)
Sets the limiter output gain
Attack
Sets the attack time
c
Release
Sets the release time
[CH/FL] LFO (LFO Waveform)
Selects the LFO waveform of the chorus/flanger
d
F (LFO Frequency)
Sets the LFO speed
Dly (Delay Time)
Sets the delay time
Dep (Depth)
e
Sets the depth of LFO modulation
Feedback
Sets the feedback amount
[F] EQ Trim
f
Sets the EQ input level
[F] Pre LEQ Gain [dB]
Sets the gain of Low EQ
g
Pre HEQ Gain [dB]
Sets the gain of High EQ
[F] Cho/Flng W/D
Sets the effect balance of the chorus/flanger
h
Output Mode
Selects the output mode for the chorus/flanger
Routing
i Switches the order of the limiter and chorus/flanger connection
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
j
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
188
Routing
Chorus/Flanger
Chorus/Flanger
Normal
LEQ HEQ
+
–
Wet Invert
Feedback
Cho/Flng Wet / Dry
LFO: Tri / Sine
1.0:1...50.0:1, Inf:1
–Inf, –38...+24dB
0.02...20.00Hz
–Wet...–2:98, Dry, 2:98...Wet
Normal, Wet Inv
LMT→CH/FL, CH/FL→LMT
Dry, 1:99...99:1, Wet
072: Limit–Phaser
This effect combines a mono-type limiter and a phaser. You
can change the order of the effect connection.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Wet / Dry
+
Output Mode
Right
Wet / Dry
[LMT] Ratio
a
Sets the signal compression ratio
Threshld (Threshold)
Fx:003
Sets the level above which the compressor is applied
b
–40...0dB
G.Adj (Gain Adjust)
Fx:003
Sets the limiter output gain
Attack
Fx:003
Sets the attack time
c
1...100
Release
Fx:003
Sets the release time
1...100
[PHS] LFO (LFO Waveform)
Fx:003
Selects the LFO waveform of the phaser
d
Tri, Sine
F (LFO Frequency)
Sets the LFO speed
Manu (Manual)
Sets the frequency to which the effect is applied
0.0...50.0ms
Dep (Depth)
e
Sets the depth of LFO modulation
0...100
Resonance
Sets the resonance amount
–100...+100
[P] Phaser W/D
Fx:020
Sets the phaser effect balance
f
0...100
Output Mode
Selects the phaser output mode
–15...+15dB
Routing
g
Switches the order of the limiter and phaser connection
–15...+15dB
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
Fx:010, 020 h
Selects the modulation source of the effect balance
(Amount)
Fx:067
Sets the modulation amount of the effect balance
Fx:067
Off...Tempo
–100...+100
Routing
Limiter
Phaser
Limiter Phaser
Gain Adjust
Resonance
LFO: Tri / Sine
Envelope - Control
–Wet...–2:98, Dry, 2:98...Wet
Wet / Dry
Normal
+
Output Mode
–
Wet Invert
Phaser Wet / Dry
Wet / Dry
1.0:1...50.0:1, Inf:1
Fx:003
–40...0dB
Fx:003
–Inf, –38...+24dB
Fx:003
1...100
Fx:003
1...100
Fx:003
Tri, Sine
0.02...20.00Hz
0...100
0...100
–100...+100
Fx:023
Fx:010, 023
Normal, Wet Inv
Fx:067
LMT→PHS, PHS→LMT
Fx:067
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100