2: All Notes; Global 4.1: Category Name; 1: P.0; 2: P.8 - Korg Triton-Rack Parameter Manual

2 Select the copy source scale ("From").
If you select Pure Major or Pure Minor, you must also
specify the "Key" selection located at the right.
Stretch can be selected only if "To" is the User All Notes
Scale.
3 Select the copy destination scale ("To").
4 To execute the Copy Scale command press the [F8]
("OK") key. To cancel without executing press the [F7]
("Cancel") key.
3.1–2: All Notes
3.1–2a
3.1–2a: User All Notes Scale
Tune
Here, you can make independent pitch settings for each of
the 128 notes.
Adjust the pitch of each of the 128 notes (C–1 – G9) in one-
cent steps. This adjustment is relative to equal temperament.
A setting of –99 lowers the pitch approximately a semitone
below normal pitch.
A setting of +99 raises the pitch approximately a semitone
above normal pitch.
In the case of the "User All Notes Scale," you can select
Stretch in the Utility menu command "Copy Scale" (3.1–1b).
Use the [ ], [ ] keys to select the key that you wish to
set. You can also select the key by holding down the
[ENTER] key and playing a note on the keyboard of a
connected MIDI instrument.
Key Select
This indicates the location of the key displayed in "Tune."
You can use the [ ], [ ] keys to move in one-octave steps.
"Tune"
Indicates that there
are keys to the left.
Key Select
3.1–2b: UTILITY
"Write Global Setting" (1.1–1d), "Copy Scale" (3.1–1b)

GLOBAL 4.1: Category Name

4.1–1: P.0..7
4.1–2: P.8..15
4.1–3: C.0..7
4.1–4: C.8..15
Here you can assign names to the program and combination
categories.
Select the category whose name you wish to modify, press
the [F5] ("TEXT") key to access the text dialog box, and
input the name.
A maximum of 16 characters can be input ( BG p.38).
The category names you edit here can be selected in the dia-
log box when you write a program or combination.
3.1–2b
With the factory settings, these are classified by type of
instrument.
You can specify sixteen categories each for programs and
combinations.
The category names you edit here can be specified
[–99...+99]
when you write data in the "Write Program dialog box"
(PROG 1.1–d: UTILITY) or "Write Combination dialog
box" (COMBI 1.1–d: UTILITY), and used in the respec-
tive "Select by Category" function to select programs or
combinations by category.
4.1–1a
4.1–3a
[C–1...G9]
If you want the edited user categories to be backed up
Indicates that there
are keys to the right. when the power is turned off, you must write them into
memory. Select the Utility "Write Global Setting" to
access the Write Global Setting dialog box, or press the
[WRITE] key to display the Update Global settings dia-
log box and press the [F8] ("OK") key to write the
edited settings.
4.1–1 (...4)a: Category
Selects the category name that you wish to edit.
4.1–1 (...4)b: TEXT
Edits the category name.
Press the [F5] ("TEXT") key to access the text dialog box.
For the editing procedure refer to BG p.38.
4.1–1 (...4)c: UTILITY
"Write Global Setting" (1.1–1d)
(Prog.00–07)
(Prog.08–15)
(Comb.00–07)
(Comb.08–15)
4.1–1b
4.1–3b
4.1–1c
4.1–3c
115