Program Mode; Prog Page Menu - Korg Triton-Rack Parameter Manual

PROG PAGE MENU

Use the following procedure to select the desired page
within the mode.
1 Press the [MENU] key to access the "PAGE MENU."
The "PAGE MENU" will show an abbreviated name for
each page.
2 Use the [F1]–[F7] keys at the bottom of the page to select
the desired page. Pressing the same key will move down-
ward. You can also move by using the [ ], [
[ ] keys.
3 Press the [F8] ("Open") key to access the page.
4 If the selected page contains two or more tab pages, press
the nearest [F1]–[F7] key below the tabs to select the
desired tab page.
Other ways to select a page
• You can also move to the desired page by holding down
the [MENU] key and using numeric keys [0]–[9] to enter
a two-digit page number. For example if you wish to
access the 5.3: Ed-LFOs page, hold down the [MENU]
key and consecutively press numeric keys [5] and then
[3].
• By holding down the [MENU] key and using the cursor
keys [ ](–) or [ ](+), you can step through the pages
forward or backward in the order of 1.1→2.1→2.2→3.1,
etc.

1. Program mode

Play
Basic 2.1: Ed-Basic
Ctrl
OSC
Pitch 3.1: Ed-Pitch
], [ ],
Flt1
Flt2
Amp1 5.1: Ed-Amp1
Amp
Amp2 5.2: Ed-Amp2
EG
LFO
Arp
BUS
IFX
MFX
1.1: Play Select and play programs. Use the Perfor-
mance Editor for easy editing, and to do
simple editing of arpeggio patterns. (
Set basic program parameters such as
Oscillator and Multisample, and make set-
tings for the Audition function. (
2.2: Ed-Ctrl Controller settings. (
2.3: Ed-OSC This will be displayed when you select bank
I–F if the optional EXB-MOSS is installed.
OSC settings for the MOSS tone generator.
( p.10)
Pitch settings. Pitch EG settings. ( p.10)
4.1: Ed-Filter1 Filter 1 (tone) settings. Filter EG settings.
( p.14)
4.2: Ed-Filter2 Filter 2 (tone) settings. Filter EG settings.
( p.19)
Amp 1 (volume) settings. Amp EG, pan
(position) settings. (
5.1: Ed-Amp This will be displayed when you select bank
I–F if the optional EXB-MOSS is installed.
Amp (volume) settings. Amp EG, pan (posi-
tion) settings.
Amp 2 (volume) settings. Amp EG, pan
(position) settings. (
5.2: Ed-EGs This will be displayed when you select bank
I–F if the optional EXB-MOSS is installed.
EG settings.
5.3: Ed-LFOs Type and speed settings etc. for the two
LFOs provided for each oscillator. (Make
settings in the pitch, filter, and amp pages
to specify the depth of the LFO settings you
make here.) ( p.23)
6.1: Ed-Arp. Arpeggiator settings. (Shared with 1.1: Play
parameters. You may edit either.) (
7.1: Ed-BUS Select the BUS and master effect send
level for the oscillator output. (
7.2: Ed-InsertFX Insert Effect routing, selection and settings.
( p.28)
7.3: Ed-Mas- Master Effect selection and settings. Master
terFX EQ settings. ( p.29)
p.2)
p.5)
p.9)
p.19)
p.22)
p.24)
p.26)
1