Korg Triton-Rack Parameter Manual page 84

The remaining amount of memory will depend on the fol-
lowing conditions.
1. The amount of memory that is installed.
2. Whether the sample is stereo or mono. When the "Mode
(Sample Mode)" (1.1–2a) is set to Stereo, the memory
capacity will be halved.
3. The time specified for "Pre Trigger" (1.1–2b: a function
that automatically samples the sound even before you
begin sampling) will be subtracted from the amount of
memory that actually remains.
Bank (RAM Bank)
Selects the memory bank into which you will sample. The
sample data memory is organized into six banks, each with
16 Mbytes. The TRITON-Rack comes with 16 Mbytes of
memory (SIMM) installed as standard. In this case, (RAM)1
will always be selected as the memory bank, and it will not
be possible to select (RAM)2, 3, 4, 5 or 6.
By installing separately sold 72-pin SIMM boards you can
expand the memory to a maximum of 96 Mbytes (three 32
Mbyte SIMM boards) ( p.243).
Installed SIMM boards and available banks
SIMM Slot No. SIMM
Slot1 16 Mbyte (factory-installed)
32Mbyte
Slot2 16Mbyte
32Mbyte
Slot3 16Mbyte
32Mbyte
On the TRITON-Rack, a 16 Mbyte SIMM is factory-
installed in slot 1. For "Bank (RAM Bank)" you can
select 1. For example if slot 1 contains the factory-
installed 16 Mbyte SIMM and you have installed a 32
Mbyte SIMM in slot 2 and a 16 Mbyte SIMM in slot 3,
"Bank (RAM Bank)" can be set to 1 (16 Mbyte), 3 (16
Mbyte), 4 (16 Mbyte), or 5 (16 Mbyte). Banks are in 16
Mbyte units.
(If 32 Mbyte SIMMs are installed in slot 1, slot 2, and
slot 3, you will be able to select all banks, and the total
capacity will be 96 Mbytes.)
Mode (Sample Mode)
Select s the channel(s) to be sampled, to specify whether a
mono or a stereo sample will be recorded.
Depending on the "Input1, Input2" (1.1–3a) settings, the
external source from the AUDIO INPUT 1 and 2 jacks will be
sent, either as direct sound without being routed through an
effect, or as effect-processed sound routed through an inser-
tion effect, to the L/R bus and sampled from the internal L
and R channels.
L-Mono: The sound of the internal L channel will be sam-
pled in mono.
R-Mono: The sound of the internal R channel will be sam-
pled in mono.
Stereo: The sound of the internal L and R channels will be
sampled in stereo. When you sample in stereo, a stereo mul-
tisample or sample will be created.
[1...6]
Bank (RAM Bank)
1
1, 2
3
3, 4
5
5, 6
[L-Mono, R-Mono, Stereo]
Example 1:
Sampling a monaural source connected to AUDIO INPUT 1
without applying internal effects
Input1 "Lvl (Level)" (1.1–3a)
Input1 "Pan" (1.1–3a)
Input1 "BUS (BUS(IFX)Select)"(1.1–3a)
"Recording Level" (1.1–2c, 1.1–3e)as appropriate
"Mode (Sample Mode)" (1.1–2a)
Example 2:
A monaural source connected to AUDIO INPUT 1 routed
through the internal insertion effect IFX 052: Rev Hall, and
sampled in stereo
Input1 "Lvl (Level)" (1.1–3a)
Input1 "Pan" (1.1–3a)
Input1 "BUS (BUS(IFX)Select)"(1.1–3a)
IFX select (7.2) 052: Reverb Hall
and make settings
"Recording Level" (1.1–2c, 1.1–3e)as appropriate
"Mode (Sample Mode)" (1.1–2a)
Example 3:
A stereo source connected to AUDIO INPUT 1 and 2, and
sampling without applying internal effects
Input1 "Lvl (Level)" (1.1–3a)
Input1 "Pan" (1.1–3a)
Input1 "BUS (BUS(IFX)Select)"(1.1–3a)
Input2 "Lvl (Level)" (1.1–3a)
Input2 "Pan" (1.1–3a)
Input2 "BUS (BUS(IFX)Select)"(1.1–3a)
"Recording Level" (1.1–2c, 1.1–3e)as appropriate
"Mode (Sample Mode)" (1.1–2a)
Example 4:
A stereo source connected to AUDIO INPUT 1 and 2, routed
through internal insertion effect IFX1 008: St.Graphic 7EQ,
and sampled in stereo
Input1 "Lvl (Level)" (1.1–3a)
Input1 "Pan" (1.1–3a)
Input1 "BUS (BUS(IFX)Select)"(1.1–3a)
Input2 "Lvl (Level)" (1.1–3a)
Input2 "Pan" (1.1–3a)
Input2 "BUS (BUS(IFX)Select)"(1.1–3a)
IFX1 select (7.2) 008: St.Graphic
7EQ and make settings
"Recording Level" (1.1–2c, 1.1–3e)as appropriate
"Mode (Sample Mode)" (1.1–2a)
When you finish recording a stereo sample, you may
hear a slight noise. This does not affect the audio data
that has been sampled.
1.1–2b: REC Setup
Mode (REC Mode)
Select s the method by which sampling will be started.
Manual: Sampling will start when you press the [F5]
("START") key from the sampling standby condition.
1 Press the [F4] ("REC") key to enter sampling standby
mode.
2 Use the "Recording Level" (1.1–2c, 1.1–3e) slider to
adjust the sampling level.
Be careful of changes in the monitoring volume level
( "Recording Level").
127
L000
L/R
L-Mono
127
C064
IFX1
Stereo
127
L000
L/R
127
R127
L/R
Stereo
127
L000
IFX1
127
R127
IFX1
Stereo
[Manual, Auto]
77