Multi 4.3: Midi Filter3; 1: M3-1; 2: 3-1; 3: 3-2 - Korg Triton-Rack Parameter Manual

MULTI 4.3: MIDI Filter3

Specifies whether the A- and B-mode operations of REAL-
TIME CONTROLS knobs [1]–[4] will be received. MIDI con-
trol messages are fixed as the A-mode operation of each
knob. In B-mode the knobs correspond to the messages you
assign in the 2.2: Controller Ctrls page.
4.3–1: M3–1..8
4.3–2: 3–1..16
4.3–3: 3–2..8
(MIDI Filter3–2 T01–08)
4.3–4: 3–2..16
4.3–1a
4.3–1(2)a: Realtime Control Knob 1, 2
Knob1
Specifies whether or not the A-mode [1] knob MIDI control
change message #74 (the TRITON-Rack's low pass filter cut-
off frequency) and the B-mode [1] knob MIDI control change
message will be received.
Knob2
Specifies whether or not the A-mode [2] knob MIDI control
change message #71 (the TRITON-Rack's low pass filter res-
onance or high pass filter cutoff frequency) and the B-mode
[2] knob MIDI control change message will be received.
4.3–3(4)a: Realtime Control Knob 3, 4
Knob3
Specifies whether or not the A-mode [3] knob MIDI control
change message #79 (the TRITON-Rack's filter EG intensity)
and the B-mode [3] knob MIDI control change message will
be received.
Knob4
Specifies whether or not the A-mode [4] knob MIDI control
change message #72 (the release time of the TRITON-Rack's
filter and amp EG's) and the B-mode [4] knob MIDI control
change message will be received.
4.3–1(2)b, 4.3–3(4)b: UTILITY
"Memory Status," "Rename Multi," "Delete Multi,"
"Copy From Multi," "Copy From Combi," "Load Tem-
plate Multi," "Save Template Multi" (1.1–1c)
60
(MIDI Filter3–1 T01–08)
(MIDI Filter3–1 T09–16)
(MIDI Filter3–2 T09–16)
[Off, On]
[Off, On]
[Off, On]
[Off, On]

MULTI 4.4: MIDI Filter4

Specifies whether the operations of "SW1" and "SW2" will
be received. "SW1" and "SW2" correspond to the messages
you assigned in 2.2: Controller. Here you can also specify
whether other control changes will be received.
4.4–1: M4–1..8
4.4–2: 4–2..16
4.4–1a
4.4–1(2)a: SW1, SW2
4.3–1b
SW1, SW2
Specifies whether the operations of "SW1" and "SW2" will
be received.
This setting is valid if you have selected SW1 Mod. (CC#80),
SW2 Mod. (CC#81), or Porta.SW (CC#65).
4.4–1(2)b: UTILITY
"Memory Status," "Rename Multi," "Delete Multi,"
"Copy From Multi," "Copy From Combi," "Load Tem-
plate Multi," "Save Template Multi" (1.1–1c)
4.4–3: 4–2..8
4.4–4: 4–2..16
4.4–3a
4.4–3(4)a: Other Control Change
Other Ctrl Change
Specifies whether or not MIDI control change messages
other than those included in MIDI Filter 1–4 will be
received.
4.4–3(4)b: UTILITY
"Memory Status," "Rename Multi," "Delete Multi,"
"Copy From Multi," "Copy From Combi," "Load Tem-
plate Multi," "Save Template Multi" (1.1–1c)
(MIDI Filter4–1 T01–08)
(MIDI Filter4–1 T09–16)
(MIDI Filter4–2 T01–08)
(MIDI Filter4–2 T09–16)
4.4–1b
[Off, On]
4.4–3b
[Off, On]