Prog 5.1: Ed-Amp; Prog 5.2: Ed-Amp2; 1: Lvl/Pan (Level/Pan); 2: Mod. (Amp2 Modulation) - Korg Triton-Rack Parameter Manual

parameter, positive (+) values of "Ramp (Ramp Setting)"
will cause EG times to be lengthened, and negative (–) val-
ues of "Ramp (Ramp Setting)" will cause EG times to be
shortened. The direction of the change is specified by "A
(AMS1 SW Attack)," "D (AMS1 SW Decay)," "S (AMS1 SW
Slope)," and "R (AMS1 SW Release)."
When "AMS1 (Time Mod. AMS1)" is Velocity, positive (+)
values will cause EG times to lengthen as you play more
strongly, and negative (–) values will cause EG times to
shorten as you play more strongly. With a setting of 0, the EG
times will be as specified in "Amp1 EG" (5.1–3a).
A (AMS1 SW Attack)
Specifies the direction of the effect that "AMS1 (Time Mod.
AMS1)" will have on "A (Attack Time)." With positive (+)
values of "I (AMS1 Intensity)," setting this parameter to +
will allow AMS1 to lengthen the time, and setting it to – will
allow AMS1 to shorten the time. With a setting of 0 there
will be no effect.
D (AMS1 SW Decay)
Specifies the direction of the effect that "AMS1 (Time Mod.
AMS1)" will have on "D (Decay Time)." With positive (+)
values of "I (AMS1 Intensity)," setting this parameter to +
will allow AMS1 to lengthen the time, and setting it to – will
allow AMS1 to shorten the time. With a setting of 0 there
will be no effect.
S (AMS1 SW Slope)
Specifies the direction of the effect that "AMS1 (Time Mod.
AMS1)" will have on "S (Slope Time)." With positive (+)
values of "I (AMS1 Intensity)," setting this parameter to +
will allow AMS1 to lengthen the time, and setting it to – will
allow AMS1 to shorten the time. With a setting of 0 there
will be no effect.
R (AMS1 SW Release)
Specifies the direction of the effect that "AMS1 (Time Mod.
AMS1)" will have on "R (Release Time)." With positive (+)
values of "I (AMS1 Intensity)," setting this parameter to +
will allow AMS1 to lengthen the time, and setting it to – will
allow AMS1 to shorten the time. With a setting of 0 there
will be no effect.
Amp 1 EG changes (Time)
(AMS=Amp KTrk +/+, Intensity = a positive (+) value)
(When Amp Keyboard Track (5.1–2a) Low Ramp= a positive (+) value, and
High Ramp = a positive (+) value)
Note-on
Note-off
Settings of 5.1–3a: Amp 1 Low-pitched note played
EG with "A," "D," "S", and "R"
at +
Amp 1 EG changes (Time) (AMS=Velocity, Intensity= a positive (+) value)
Note-on
Note-off
Softly played note with "A," Strongly played note with
"D," "S" and "R" at + (settings "A," "D," "S" and "R" at +
of 5.1–3a: Amp 1 EG)
22
Note-on Note-on
Note-off
High-pitched note played
with "A," "D," "S", and "R"
at –
Note-on Note-on
Note-off
Strongly played note with
"A," "D," "S" and "R" at –
AMS2 (Time Mod. AMS2)
I (AMS2 Intensity)
A (AMS2 SW Attack)
D (AMS2 SW Decay)
S (AMS2 SW Slope)
R (AMS2 SW Release)
These parameters specify how "AMS2 (Time Mod. AMS2)"
will control the amp 1 EG "Time" parameters ( "AMS1
(Time Mod. AMS1)"–"R(AMS1 SW Release)").
[–, 0, +]
5.1–3d: UTILITY
"Write Program" (1.1–1d), "Copy Oscillator," "Swap
[–, 0, +]
Oscillator" (2.1–1d)
Sync Both EGs
If you select "Sync Both EGs" from the Utility menu and
press the [F8] key, a check mark will appear at the left of
"Sync Both EGs." In this state, the amp 1 EG and the amp 2
EG can be edited simultaneously. (Editing either one will
cause the other to change.) ( 4.1–5d
[–, 0, +]
This page is displayed if the separately sold EXB-MOSS
[–, 0, +]
option is installed.
( EXB-MOSS owner's manual & p.251 "EXB-MOSS
option")
Indicates settings for amp 2 which controls the volume of
oscillator 2. Pan settings are also made here.
Note-off
5.2–1: Lvl/Pan
5.2–2: Mod.
5.2–3: EG
These will appear when "Mode (Oscillator Mode)" (2.1–1a)
Note-off
is Double. ( "5.1: Ed–Amp1")
This page is displayed if the separately sold EXB-MOSS
option is installed.
( EXB-MOSS owner's manual & p.251 "EXB-MOSS
option")
PROG 5.1: Ed–Amp
PROG 5.2: Ed–Amp2
(Level/Pan)
(Amp2 Modulation)
(Amp2 EG)
PROG 5.2: Ed–EGs
[Off, (EXT, KT)]
[–99...+99]
[–, 0, +]
[–, 0, +]
[–, 0, +]
[–, 0, +]
)