2: Route (Routing) - Korg Triton-Rack Parameter Manual

CC#93 will control the Send 1 level for OSC 1 and 2,
and control change #91 will control the Send 2 level for
OSC 1 and 2. These are controlled on the global MIDI
channel "MIDI Channel" (GLOBAL 2.1–1a).
The actual send level is determined by multiplying
these values with the send level setting of each oscilla-
tor.
7.1–1b: Use DKit Setting
The LCD screen shown below is for when "Mode (Oscillator
Mode)" (2.1–1a) is set to Drums.
7.1–1b
Use DKit Setting
This will be available when "Mode (Oscillator Mode)" is set
to Drums.
On (Checked): The "BUS (BUS Select)" (GLOBAL 5.1–3a)
setting for each key of the selected drum kit will be used.
Check this when you want to apply an insert effect to an
individual drum instrument, or to output an individual
drum instrument to one of the AUDIO OUTPUT (INDIVID-
UAL) jacks.
If the "Mode (Oscillator Mode)" is Single or Double, this
setting has no effect.
Off (Unchecked): The setting of the "BUS Select,""MFX
Send" (7.1–1c) parameter described below will be used. All
drum instruments will be sent to the specified bus.
7.1–1c: UTILITY
"Write Program" (1.1–1d)
For details on how to select the desired utility function, refer
to "PROG 1.1–1d: UTILITY."
Copy Insert Effect
This command copies effect settings from Program, Combi-
nation, Multi, or Sampling mode.
1 Select "Copy Insert Effect" to access the dialog box.
2 In "From" select the copy source mode, bank, and num-
ber.
You can use the [BANK] and [A]–[H] keys to select the
bank.
3 Select the effect that you wish to copy. You can also copy
from a master effect. If "All" is checked, all effect settings
will be copied (i.e., the contents of the InsertFX page and
the effect parameters of IFX 1–5, but not "Ctrl Ch").
If you are copying from a master effect, the result may
not be identical, due to differences in the routing and
level settings of a master effect.
4 Select the copy destination insert effect. If you check
"Post IFX Mixer Setting," the "Chain," "Pan (CC#8),"
"BUS Select," "S1 (Send1(MFX1))" and "S2
(Send2(MFX2))" settings that follow the copy source
insert effect will also be copied. If this is unchecked, only
the effect type and its parameters will be copied.
5 To execute the Copy Insert Effect command, press the
[F8] ("OK") key. To cancel, press the [F7] ("Cancel") key.
Swap Insert Effect
This command swaps (exchanges) insert effect settings.
1 Select "Swap Insert Effect" to access the dialog box.
7.1–1c
2 In "Source 1" and "Source 2," select each of the insert
effects that you wish to swap.
3 To execute the Swap Insert Effect command, press the
[Off, On]
[F8] ("OK") key. To cancel, press the [F7] ("Cancel") key.
7.1–2: Route
7.1–2a
7.1–2a: Routing
This displays the setting status of the insert effects.
This shows the insert effect routing, the names of the
selected effects, their on/off setting, and chain status. The
insert effect type, on/off, and chain settings can be made in
the Setup page of 7.2: Ed-InsertFx.
You can use the [INC], [DEC] keys and [VALUE] dial to set
"BUS Select" ( 7.1–1a).
7.1–2b: UTILITY
"Write Program" (1.1–1d), "Copy Insert Effect," "Swap
Insert Effect" (7.1–1c)
(Routing)
7.1–2b
27