Korg Triton-Rack Parameter Manual page 40

1.1–2c: Program Select, Program Name
Program Select
Selects the program that will be used by each timbre.
When "Program Select" is selected, you can use the [BANK]
key, numeric keys [0]–[9], [VALUE] dial, and [INC], [DEC]
keys to select a program.
You can move to timbres "T1"–"T8" by holding down the
[TIMBRE/TRACK] key and pressing one of the [F1](1/9)–
[F8](8/16) keys.
"Program Select" settings can also be made in the Prog page
of 2.1: Ed-Prog/Mix.
You can also use Utility "Select by Category" to select pro-
grams by category.
Bank I–F can be selected if you have installed the sepa-
rately sold EXB-MOSS option. When installed, the 128
special EXB-MOSS programs will be available.
If bank select and program change messages are
received on a MIDI channel that matches the MIDI
channel of a timbre whose "Status" is INT, the program
of that timbre will change. However if the MIDI chan-
nel of the incoming message matches the global MIDI
channel "MIDI Channel," then the combination will
change.
If you do not want the combination to change, you can
either change the global MIDI channel so that it does
not match the channel on which the program change
messages are being received, or you can uncheck
"Combi (Combi Change)" (GLOBAL 2.1–1b). Alter-
nately, you can uncheck "Bank (Bank Change)" (GLO-
BAL 2.1–1b) so that only the program number will
change and the bank will remain the same.
If you wish to change a program without changing the
combination, you can also set "Program Change" (4.1–
1a) so that the program will change on certain timbres
but not on others.
When you select a combination on the TRITON-Rack, a
MIDI program change for the selected combination
number will be transmitted on the global MIDI channel
"MIDI Channel" (GLOBAL 2.1–1a). At the same time,
bank select, program change, and volume (CC#7) mes-
sages will be transmitted on the MIDI channel specified
for each timbre that is set to "Status" (3.1–1a) of EXT or
EX2. However, these messages will not be transmitted
for timbres that are set to the same MIDI channel as the
global MIDI channel. In this case, EX2 timbres will
show the "Program Select" Bank as "–", and will trans-
mit the bank number that was specified in "Bank (EX2)
MSB"and "Bank (EX2) LSB" (3.1–1a).
MIDI messages transmitted when you operate the TRI-
TON are transmitted on the global MIDI channel. At
the same time, timbres whose "Status" is EXT or EX2
will transmit the same messages on their own MIDI
channel.
Program Name
This displays part of the program name selected for the tim-
bre. In the case of the GM2 variation bank or the GM2
drums bank, the variation bank (1)–(9) or drums bank (d)
will be indicated.
1.1–2d: Selected Timbre Information
[I-A000...E-H127]
This shows information on the timbre (1–8) that is currently
selected for editing.
Timbre No.: Bank No., Prog No.: and name
This shows the timbre number, and the program bank, num-
ber and name selected for that timbre.
Status
This shows the MIDI and internal tone generator status for
each track.
Ch
This is the MIDI channel number specified for the timbre.
1.1–2e: UTILITY
"Write Combination," "Solo Selected Timbre" (1.1–1d)
For details on how to select the desired utility function, refer
to "PROG 1.1–1d: UTILITY."
Select by Category
Combinations or the programs used by each timbre can be
selected by category.
If you have selected "Combi Select," selecting Utility
"Select by Category" will access the Select Combination by
Category dialog box, allowing you to select a combination
by category. ( p.32)
If you have selected "Program Select," selecting Utility
"Select by Category" will access the Select Program by Cate-
gory (Timbre) dialog box, allowing you to select a program
for each timbre by category.
For the procedure of selecting by category, refer to p.2.
(INT, Off, EXT, EX2)
(01...16, Gch)
33