094: Mlttap Chodly (Multitap Chorus/Delay); 095: St.pitch Shift (Stereo Pitch Shifter); L Delay (L Delay Time); Sets The Delay Time For The Left Channel - Korg Triton-Rack Parameter Manual

094: MltTap ChoDly
(Multitap Chorus/Delay)
This effect has six chorus blocks with different LFO phases.
You can produce a complex stereo image by setting a different
delay time and depth for each block. You can control the delay
output level via a modulation source.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Feedback
Tap1 Delay
Tap2 Delay
Tap3 Delay
+
Tap4 Delay
Tap5 Delay
Tap6 Delay
Right
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
LFO: Triangle
D -mod
On/Off Control
LFO Freq (LFO Frequency)
a
Sets the LFO speed
T1(000) (Tap1 Delay)
Sets the Tap1 (LFO phase=0 degrees) delay time
D (Depth)
b Sets the Tap1 chorus depth
S (Staus)
Selects on, off, or modulation source for the control of Tap1 output
T2(180) (Tap2 Delay)
Sets the Tap2 (LFO phase=180 degrees) delay time
D (Depth)
c Sets the Tap2 chorus depth
S (Staus)
Selects on, off, or modulation source for the control of Tap2 output
T3(060) (Tap3 Delay)
Sets the Tap3 (LFO phase=60 degrees) delay time
D (Depth)
d Sets the Tap3 chorus depth
S (Staus)
Selects on, off, or modulation source for the control of Tap3 output
T4(240) (Tap4 Delay)
Sets the Tap4 (LFO phase=240 degrees) delay time
D (Depth)
e Sets the Tap4 chorus depth
S (Staus)
Selects on, off, or modulation source for the control of Tap4 output
T5(120) (Tap5 Delay)
Sets the Tap5 (LFO phase=120 degrees) delay time
D (Depth)
f Sets the Tap5 chorus depth
S (Staus)
Selects on, off, or modulation source for the control of Tap5 output
T6(300) (Tap6 Delay)
Sets the Tap6 (LFO phase=300 degrees) delay time
D (Depth)
g Sets the Tap6 chorus depth
S (Staus)
Selects on, off, or modulation source for the control of Tap6 output
Panning (Panning Preset)
h
Specifies the stereo image of each Tap
198
Wet / Dry
Wet / Dry
Panning Preset
0.02...13.00Hz
0...570ms
0...30
On, Off, On→Off, Off→On
,
0...570ms
0...30
On, Off, On→Off, Off→On
,
0...570ms
0...30
On, Off, On→Off, Off→On
,
0...570ms
0...30
On, Off, On→Off, Off→On
,
0...570ms
0...30
On, Off, On→Off, Off→On
,
0...570ms
0...30
On, Off, On→Off, Off→On
,
1, 2, 3, 4
T1 Fb (Tap1 Feedback)
Sets the Tap1 feedback amount
(Source)
i Selects the modulation source for the Tap output level, feedback
amount, and effect balance
(Amount)
Sets the modulation amount of Tap1 feedback amount
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
j
(Amount)
Sets the modulation amount of the effect balance
b: S, c: S, d: S, e: S, f: S, g: S
These parameters set the output status of each Tap.
On: Output is always on. (No modulation)
Off: Output is always off. (No modulation)
On→Off: Output level is switched from on to off depending on
the modulation source.
Off→On: Output level is switched from off to on depending on
the modulation source.
Combining these parameters, you can change from 4-phase cho-
rus to two-tap delay by crossfading them gradually via the modu-
lation source during a performance.
h: Panning
This parameter selects combinations of stereo images of the tap
outputs.
i: (Source), i: (Amount), j: (Amount)
Tap output level, feedback amount and effect balance are con-
trolled simultaneously via a modulation source.
095: St.Pitch Shift
(Stereo Pitch Shifter)
This is a stereo pitch shifter. The pitch shift amount for the left
and right channels can be reversed from each other.
Stereo In - Stereo Out
Left
Pitch Shifter
Input Level
Pre
Feedback Position
Pre
Input Level
Pitch Shifter
Right
Mode
Switches Pitch Shifter mode
a
L/R (L/R Pitch)
Determines whether or not the L/R pitch shift amount is inverted
Shift (Pitch Shift)
Sets the pitch shift amount in steps of a semitone
(Source)
b
Selects the modulation source of pitch shift amount
(Amount)
Sets the modulation amount of pitch shift amount
Fine
Sets the pitch shift amount in steps of one cent
c
(Amount)
Sets the modulation amount of pitch shift amount

L Delay (L Delay Time)

d

Sets the delay time for the left channel

R Delay (R Delay Time)

e

Sets the delay time for the right channel

Feedback Position
f
Switches the feedback connection
–100...+100
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
–100...+100
Wet / Dry
High Damp
Delay
Post
Feedback Spread
Post
Delay
High Damp
Wet / Dry
Slow, Medium, Fast
Fx:038
Normal, Up/Down
–24...+24
Fx:038,
Off...Tempo
Fx:038
–24...+24
Fx:038
–100...+100cent
Fx:038,
–100...+100cent
Fx:038
0...1000ms
0...1000ms
Pre, Post
Fx:038