102: Hold Delay; (Source) Off; Selects The Modulation Source Of The Effect Balance; (Amount) -100 - Korg Triton-Rack Parameter Manual

W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
i

Selects the modulation source of the effect balance

(Amount)

Sets the modulation amount of the effect balance

f: Time Over? L >, f: R >
You can set the delay time up to 1365msec. If the delay time
exceeds this limit, the error message "OVER!" appears on the dis-
play. Set the delay time parameters so that this message will not
appear. "Time Over?>" is only a display parameter.

102: Hold Delay

This effect records the input signal and plays it back repeat-
edly. You can control the start of recording and reset via a
modulation source. Easy to use for real-time performances.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Loop Time: Auto/ ...2700ms
Right
D -mod
REC Control
D -mod
RST Control
Loop Time
a
Sets Automatic loop time setup mode or specifies loop time
REC Control Src
b
Selects control source for recording
RST Control Src
c
Selects control source for reset
Manual REC Ctrl
d
Sets the recording switch
Manual RST Ctrl
e
Sets the reset switch
Pan
Sets the stereo image of the effect
(Source)
f
Selects the modulation source of stereo image of the effect
(Amount)
Sets the modulation amount of stereo image of the effect
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
g
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
a: Loop Time
With Auto, the loop time is automatically set. Otherwise, you can
specify the loop time.
When Auto is selected, the Loop Time is automatically set to the
time it takes for a performance recorded while the Modulation
Source or "Manual REC Ctrl" is on. However, if the time length
exceeds 2,700msec, the loop time will be automatically set to
2,700msec.
b: REC Control Src, d: Manual REC Ctrl
"REC Control Src" selects the modulation source that controls
recording.
If this modulation is on, or if "Manual REC Ctrl" is set to REC On,
you can record the input signal. If a recording has already been
carried out, additional signals will be overdubbed.
202
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Wet / Dry
Delay
Pan
Wet / Dry
Auto, 1...2700ms
Off...Tempo
,
Off...Tempo
,
REC Off, REC On
Off, RESET
L100...L1, C, R1...R100
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
The effect is off when a value for the modulation source
specified for the "REC Control Src" parameter is 63 or
smaller, and the effect is on when the value is 64 or higher.
c: RST Control Src, e: Manual RST Ctrl
The "RST Control Src "parameter specifies the modulation source
that controls the reset operation.
When you set this modulatoin source to On, or "Manual RST Ctrl"
to RESET, you can erase what you recorded. If the Loop Time
parameter has been set to Auto, the loop time is also reset.
The effect is off when a value for the modulation source
specified for the "RST Control Src" parameter is 63 or
smaller, and the effect is on when the value is 64 or higher.
"Hold" procedure (when Loop Time = Auto)
Select the following options for each parameter:
1
"Loop Time [msec]"=Auto
"REC Control Src"=JS +Y#1
"RST Control Src"=JS –Y#2
"Manual REC Ctrl"=REC Off
"Manual RST Ctrl"=RESET
It should be noted that all recordings will be deleted while
Reset is On.
2
"Manual RST Ctrl"=Off
Reset is cancelled and the unit enters Rec ready mode.
3
Push the joystick of a connected MIDI instrument in the +Y
direction (forward) and play a phrase you wish to hold. When
you pull the joystick to its original position, the recording will
be finished and the phrase you just played will be held.
Loop Time is automatically set only for the first recording after
resetting. If the time length exceeds 2,700msec, Loop Time will
be automatically set to 2,700msec. (If you have set "Loop
Time" to 1–2,700msec, the specified loop time will be used
regardless of the time taken from pushing the joystick forward
until it is pulled back. However, the recording method remains
the same. The phrase being played while the joystick is pushed
forward will be held.)
4 If you made a mistake during recording, pull the joystick in
the –Y direction (back) to reset. In this way, the recording will
3
be erased. Repeat step again.
5
The recorded phrase will be repeated again and again. You can
use this to create an accompaniment.
6 By pushing the joystick in the +Y direction (forward), you can
also overdub performances over the phrase that is being held.