Page 1
Digital HD Satellite Receiver SRT 7030 User Manual...
Page 2
Digital HD Satellite Receiver SRT 7030 Supplied by STRONG Austria 13/18 V 500 mA max. COAXIAL SAT IN HDMI TV SCART S/PDIF AUDIO R/L 12 V 1.5 A MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES. DOLBY, DOLBY AUDIO AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF DOLBY LABORATORIES.
Page 3
Digital HD Satellite Receiver SRT 7030 Supplied by STRONG Austria 13/18 V 500 mA max. COAXIAL SAT IN HDMI TV SCART S/PDIF AUDIO R/L 12 V 1.5 A MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES. DOLBY, DOLBY AUDIO AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF DOLBY LABORATORIES.
Page 4
HOTLINE 0820 400 150 support_at@strong.tv Supplied by STRONG Austria Represented by STRONG Ges.m.b.H. Teinfaltstraße 8/4.Stock A-1010 Vienna, Austria Email: support_at@strong.tv 03 Mar 2022 10:29...
Page 5
Your receiver is delivered with USB multimedia support. After downloading the software for recording via USB from the website www.strong.tv, the receiver can be upgraded to support the recording and Timeshift function via USB. This user manual describes the full functionality including the recording function and may not be applicable if the software for recording via USB has not yet been installed.
Hereby, STRONG declares that the SRT 7030 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.strong.tv/en/doc Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change.
1.0 INSTRUCTION 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: To direct sunlight or any other equipment that generates heat;...
Always make backups of data on your USB storage device before using it with this receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information. STRONG cannot guarantee the playback of all files although extensions are listed, as it depends ...
2.0 YOUR RECEIVER 2.1 PIN code default: 0000 2.2 Front and side panel Fig. 1 1. LED display: Shows channel number in operation and time in Standby 2. Standby indicator: Shows power state of the receiver: RED LED - receiver is in standby mode 3.
14. MENU To open the main menu in viewing mode or to go one step back in the menu 15. Cancellation of current process/exit from main menu to viewing mode 16. VOL+/- Increases/decreases the volume level in TV mode 17.
NOTE: Sunlight or very bright light might decrease the sensitivity of the remote control. 3.0 CONNECTIONS 3.1 Basic connection using an HDMI cable Fig. 6 a) Connect the LNB of your satellite antenna to the SAT IN connector of your receiver using a good quality coax cable and suitable ‘F-connector' plugs.
NOTE: Timeshift/recording and playback only works properly when a fast USB storage device such as a USB2.0 HDD is connected to the receiver. Timeshift/ recording and playback of HD content requires a sufficient read/write speed of the used USB storage device.* * This user manual describes the full functionality including the recording function and may not be applicable if the software for recording via USB has not yet been installed.
Page 13
4.1.3 Satellite List Press p or q button to highlight satellite, press OK button select a satellite. A heart symbol will mark the selected satellite(s). RED button: Edit satellite GREEN button: Add satellite BLUE button: Delete satellite 4.1.4 Antenna Setup Motor Antenna: If you selected Motor Antenna in Antenna Connection menu, this menu allows you to change settings like LNB frequency, motor type, local longitude/local latitude, delete all,...
5.0 QUICK GUIDE FOR USING YOUR RECEIVER We at STRONG understand that you can't wait to enjoy your new HD receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your STRONG HD receiver.
6.1.1 Direct access To gain direct access to a certain channel, simply enter its number with the 0~9 keys on the remote control. Channel numbers can be up to four digits long. Entering a number with less than four digits is possible.
6.3 Selection of audio language Some channels support a choice of different audio formats and/or languages. To select another audio stream, press AUDIO in viewing mode. A list with available audio streams will now be displayed. Use pq to select a stream and confirm with OK. With the t u buttons you can choose between Mono, Mono left, Mono right or Stereo 6.4 Teletext Your receiver includes a fully featured Teletext.
7.1 Installation menu 7.1.1 Installation Here you can setup your dish and satellite parameters. Enter the menu via the Installation In this menu setting will be automatically stored upon exit without the need of confirming. Antenna Connection Enter here to select the type of satellite dish or antenna you have: Either a fixed antenna or a motor antenna Satellite List In this menu you can select the satellites for which you have a particular interest, like if they carry...
Page 18
DiSEqC1.1: To select the correct port from up to 16 (if available) for the corresponding LNB. Uncommitted DiSEqC switches in cascade can be used with this protocol. 22KHz: Auto is the setting for a Universal LNB Polarity Option are: Auto, H for horizontal and V for vertical. It will switch the LNB power as required by the transponder list.
Page 19
Limit Setup To setup the limits the dish should not exceed when moving, in case of physical obstructions. Default is disable limit (not active). If needed, the motor can physically be brought to its 0° reference position, to align the dish south when in the northern hemisphere (or north for southern hemisphere) first.
Page 20
NOTE: SatCR can only work in combination with an optional multi-output satellite splitter and a SatCR LNB, example STRONG type SRT L780 (max. 4 users). Note: SatCR cannot be combined with any other DiSEqC function. SatCR systems are mainly installed by professional experts.
Page 21
Scan Channel: Press t u to select TV+Radio, TV Channel or Radio Scan Mode: Use t u to select mode auto scan, pre-set scan or accurate Scan}. This the default mode and should be used first. Auto Scan All stored transponders in the memory will be scanned. Pre-set Scan A few satellites carry a list with transponder parameters of all transponders on that satellite.
7.1.5.1 Transponder List Transponder Edit options While in the TP list menu, you can use the coloured buttons to make changes. The options below are now available. Edit: Press RED to edit the highlighted transponder. In the pop-up banner, change the transponder´s parameters by using the pq t u and numeric buttons.
Page 23
Disable favourite TV or radio programme Repeat step 1 described above and deselect the channel in its Favourite List. Save upon Exit. View favourite programme 1. In normal viewing mode (no menu mode) press the FAV button to display a list of favourite programmes.
Rename a TV or radio programme 1. Select the programme you want to rename and press BLUE to enter the Edit section. Then use GREEN and then select the programme you want rename. A pop-up appears. 2. In the pop-up select a character by using the t u buttons. Use the numeric buttons to enter characters.
Page 25
USB has not yet been installed. ** STRONG cannot guarantee the playback of video files although extensions are listed here, as the correct playback depends on codec used, data bit rate and resolution as well. Please consult the STRONG Hotline in your country to get more details.
Page 26
YELLOW Marks a recording for deletion. When all recordings you want to delete are marked, press A message appears to confirm deleting. GREEN A recording can be locked from viewing by the password. Enter the password to set the lock. To unlock, repeat the procedure with the GREEN button. A locked recording is signalled with a Lock icon.
Page 27
During the slideshow, the orientation of the image can be rotated. tTo turn the photo t u counter clockwise. u To turn the photo clockwise. PLAY To continue slideshow after 2 or rotation of image. To stop the slide show and return to the folder view. ...
Page 28
Aspect Mode You can set the display format to available settings Auto, 16:9, 4:3PS, (Pan&Scan) and 4:3LB (Letterbox) Auto With Auto select the TV connected with HDMI will auto-negotiate the optimal setting. 16:9 For 16:9 TV screens. All programmes will fill the full screen. Content formatted in 4:3 will be stretched.
Page 29
Timer Mode Select Once for a onetime event, select Daily for each day, same time event. A free timer is default Off. Timer Service Select Channel to wake up the receiver to view the channel or Record for recording the channel. Wakeup Channel Select the channel for this event.
Page 30
WARNING: The format function will delete all data and information from your USB device or selected partition. STRONG will not take any responsibility for damaged or lost data on the USB device. An attention banner will now be displayed. Select OK to start formatting (or to cancel it). The format procedure will take some time, depending on the size of the used storage device.
Page 31
NOTE: In certain instances it can be advised on the website to upgrade the unit with the Maincode option in stead of Allcode. The bootlogo and Radioback are for Strong internal use. 7.3.7 Dump channel list 7.3.7.1 DB Management This menu allows you to save and reload the channel Data Base of your receiver from/to a USB-device.
If the receiver does not work properly after checking it, please contact your local Service line or STRONG dealer. Alternatively, you can send a support mail via our website: www.strong.tv. NEVER open or disassemble your receiver. This may cause a dangerous situation and will void the warranty.
Problem Possible cause What to do The external USB HDD The power consumption is too Connect an extra power supply adapter to does not start. high. your USB HDD device. The receiver The Auto Standby function is Set the power down time or disable it in switches to standby activated and has reached the the System Setup >...
Page 34
Picture view: JPG, BMP* * STRONG cannot guarantee the playback of files although extensions are listed, as it depends on codec used, data bit rate and resolution (all MPEG codec formats are supported). Connectors SAT IN USB 2.0 port: 5 V/500 mA (max.) supported...