Page 1
DIGITALER HD SATELLITEN RECEIVER SRT 7511 Mehr Sender in HD! Kostenloses simpli free Paket anmelden und simpli more gratis testen – für noch mehr Sendervielfalt in HD. Mit dabei: die simpliTV App. Geeignet für: ... und viele mehr! Auszug aus der simpli more Senderliste.
Page 2
Supplied by STRONG Austria Represented by STRONG Ges.m.b.H. Teinfaltstraße 8/4. Stock 1010 Vienna, Austria Email: support_at@strong-eu.com www.strong-eu.com...
Page 3
Hereby, STRONG declares that the SRT 7511 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://eu.strong-eu.com/downloads/ Subject to alterations. In consequence of continuous research and development technical speci cations, design and appearance of products may change.
TABLE OF CONTENTS 1. INTRODUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2. YOUR RECEIVER 2.1 DEFAULT PIN-CODE: 0000 2.2 Front Panel 2.3 Side Panel 2.4 Rear Panel 2.5 Remote Control 2.6 Inserting the batteries 2.7 Using the remote control 3.
Page 5
7. MAIN MENU 7.1 Installation 7.1.1 Antenna Setup 7.1.2 Motor Setting 7.1.3 Channel Search 7.1.3.1 Edit, add or delete transponders 7.1.4 Channel list selection 7.1.5 Factory Reset 7.2 Channels 7.2.1 TV Channel Manager 7.2.2 Radio Channel Manager 7.2.3 EPG (Electronic Programme Guide) 7.2.4 Parental Control 7.3 Settings 7.3.1 Language...
1. INTRODUCTION 1.1 Safety Instructions Read all of the instructions before operating the device. Keep these instructions well for later use. Only use attachments/accessories speci ed or provided by the manufacturer (such as the exclusive supply adapter, battery etc.). ...
(5 V/500 mA). If so, please connect your USB HDD to an according external power adapter. STRONG cannot guarantee compatibility with all types of USB storage devices.
It is advised not to store important information on USB storage devices used with the receiver. Always make backups of data on your USB storage device before using it with this receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information.
2. Ethernet To connect to to your home network via switch, router or modem. 3. S/PDIF (coax.) To connect to a digital ampli er or home theatre set. 4. HDMI To connect to the HDMI input of your TV set using a good quality HDMI cable. 5.
4. TV/R Toggles between TV and RADIO mode 5. No function 6. FAV Opens the favourite list selection if previously con gured 7. 9 Opens the recently watched channel list or switches between the two last previously watched channels* 8.
NOTE: The batteries must not be recharged, disassembled, electrically short-circuited, be mixed or used with other types of batteries. 2.7 Using the remote control Fig. 6 To use the remote control, point it towards the front of the digital receiver. The remote control has a range of up to 7 metres from the receiver, if properly aligned towards the IR eye on the front panel.
3. CONNECTIONS 3.1 Connection via HDMI or SCART Fig. 7 SAT IN Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. a) Connect the LNB of your satellite antenna to the SAT IN connector of your receiver using a good quality coaxial cable and suitable ‘F-connector’...
a) Connect the LNBs of your xed antenna to the desired inputs of a DiSEqC 1.0 switch using a good quality coaxial cable and suitable ‘F-connectors’ . b) Connect the output or “to receiver” of the DiSEqC 1.0 switch to the SAT IN connector on your receiver using a good quality coaxial cable and suitable ‘F-connectors’...
Connecting to a Digital Audio Ampli er with S/PDIF By connecting your receiver to a digital ampli er or home theatre system, you can enjoy the best possible sound quality and multi-channel audio (depending on broadcast). Connect your Digital Audio Ampli er or home theatre system with a suitable cinch cable to the S/PDIF connector on the back of the receiver Connecting to a digital audio ampli er and TV using HDMI If you want to connect your home theater, ampli er or AV receiver using HDMI, connect one end of a high-...
In this menu, you can choose your channel list by pressing pq. You can choose between ORF List, simpliTV List, Family List and Young Spirit, depending on your preferences and subscription (an overview about the di erent channels can be found on our website www.strong-eu. com).
NOTE: 5 min after switching the receiver into Standby it will enter the deep sleep mode. Within this time the receiver is able to start up quickly. Starting up from deep sleep takes approx. 35 seconds. 6. OPERATION In viewing mode, several features are available to make watching TV a true pleasure. This chapter describes these features.
6.1.4 Using the button In order to quickly switch between your most preferred channels, use 9 to view the list of Recently watched channels. This list contains up to 30 recently watched channels. As this list is temporary it will be recreated each time after you switch on your receiver.
6.6 Changing the video settings Press the OPT button in viewing mode to change settings like HDMI Resolution, Aspect Ratio and Aspect Conversion or to have a look on the current settings. To select use pq and to change use tu. After all settings have been made, press ...
7.1.1 Antenna Setup In this menu, you can change and adapt settings for the antenna(s) and their transponders. Use the tu buttons to change settings, and use pq to select an item, or press OK to list the settings. For the default setting of DiSEqC 1.0, you can set the parameters for up to 4 satellite positions Port 1-4.
Save / Recalculation With Save and Recalculate, you can set whether the position should be saved or a new calculation should be made after setting this position. Go to position Press OK to move the motor to the centre position. This is only necessary for the rst time to set the antenna correctly.
channel number 400 and cannot be edited. The order of the channels can be edited in My TV List therefore see chapter 7.2.1 TV Channel Manager. One Transponder: Search on the transponder selected in above. After choosing the desired settings, press OK to start the channel search, or press to exit the menu without scanning.
7.2 Channels Press MENU and use tu to select the Channels menu. The following sub-menus are available: TV Channel Manager, Radio Channel Manager, Electronic Programme Guide and Parental Control. 7.2.1 TV Channel Manager This menu allows you to customize your channel list or create favourite lists. To perform the desired action, proceed as described below.
NOTE: The simpliTV list contains channels in the sequence and numbering of the broadcaster. Added/ additional channels which are not included in the list are listed from channel number 400 and cannot be edited. The channels can be edited in My TV List, see chapter 7.2.1 TV Channel Manager 7.2.2 Radio Channel Manager Please refer to the previous chapter TV Channel Manager to nd out how it works in radio mode.
Please note that some events are broadcastwd with xed subtitles ( xed in the video signal integrated). These subtitles can not be swtiched o . Subtitle language: Set the language for the subtitles, if available, subtitles are displayed in the selected language.
minutes, 30 minutes, 1 hour, 3 hours and O . The receiver consumes less power than in standby mode. To power up from deep sleep mode, it takes about 35 seconds. Auto Standby: This function allows you to set the hours after which the receiver should automatically switch to standby mode.
7.4.1 Movies Only supported movies can be played in this menu. Use the pqtu and P + / P- buttons to navigate and select, or press OK. Signs and symbols: Press OK on this icon to go back to the main directory from a selected subdirectory. ...
7.5.2 OTA Software Update With the OTA (Over The Air) function, you can search for software updates via satellite. Ask your STRONG dealer or visit our website www.strong-eu.com for more information. Only in the case of an available update and appropriate handling the option will be available in the menu.
le back in the directory mentioned above ("ORS-CCA-S2-MM_backup"). We recommend you to always keep the backup of the original les in order so you can restore them in case of possible errors. Con rm Recover database from USB device by pressing OK and con rm the displayed message with OK to execute.
If the receiver does not work properly after checking it, please contact your local service line or STRONG dealer. Alternatively, you can send a support e-mail via our website: www. strong-eu.com. NEVER open or disassemble your receiver. This may cause a dangerous situation and will void the warranty.
Check your current subscription status Expired subscription. in CA Menu Product Status together with your service provider. To enjoy the complete range of channles and to watch your preferred scrambled services, please register with the enclosed registration form at ORF- ORF-DIGITAL-DIREKT not subscripted/ DIGITAL-DIREKT.
Page 31
Audio Decoder Audio decoding: MPEG Layer 1 & 2, Dolby Downmix Audio mode: Mono L/R, Stereo Audio support: Dolby Digital Plus* Transcoding for HDMI and S/PDIF: Dolby Digital Plus to Dolby Digital *Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories. Tuner Connector: Type1 F Type, IEC169-24, Female...