Related Manuals for Strong skylink SRT 7502
Summary of Contents for Strong skylink SRT 7502
- Page 1 Digitální HD Satelitní Přijímač SRT 7502 Pokyny k instalaci Návod na rýchlu inštaláciu Installation Instructions...
- Page 4 Děkujeme vám, že jste si koupili satelitní přijímač STRONG Děkujeme vám, že jste si koupili satelitní přijímač STRONG s vysokým rozlišením. Přejeme vám, abyste si s ním užili s vysokým rozlišením. Přejeme vám, abyste si s ním užili mnoho zábavy při sledování televize. V případě dotazů, mnoho zábavy při sledování...
- Page 5 Thank you for choosing a STRONG High Definition Satellite Receiver. We wish you great TV entertainment with it. For questions and assistance during the installation please contact your dealer or send us an email in English from our website www.strong.tv/cz/contact-form...
-
Page 6: Table Of Contents
4.5 Satellite DiSEqC Selection (Step 5) 4.6 Programme Search (Step 6) STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. -
Page 7: Introduction
1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a „ „ surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: To direct sunlight or any other equipment that generates heat;... -
Page 8: Accessories
It is advised not to store important information on USB storage devices used with the receiver. Always make backups of data on your USB storage device before using it with this receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information. -
Page 9: Side Panel
2.3 Side Panel Obr. 1b 1. Smartcard slot To insert your valid and activated Irdeto smartcard for proper reception of your desired channel bouquet. For the correct insertion of smartcard please see the insertion drawing. 2.4 Rear Panel Fig. 2 1. -
Page 10: Installing The Batteries
26. 4 Starts recording of the current broadcast 27. u Opens the Timeshift banner in viewing mode if this function is activated in the recording menu. In Multimedia and HDD Manager it starts playback of the selected file. 28. 78 During playback mode jumps to the previous / next file 29. -
Page 11: Connecting To Multiple Fixed Antennas
OPTIONAL: If your TV set doesn’t have an HDMI connector you can use the SCART connection instead. In such case connect one end of a good quality SCART cable to the TV SCART of your receiver and the other end to the SCART input of your TV set. -
Page 12: Language (Step 1)
4.1 Language (Step 1) After connecting your receiver for the first time, the Welcome 1st Step: Language menu will be shown on screen. First, choose your preferred language by using pq. After selecting, confirm by pressing OK to go to Step 2. 4.2 Audio and Subtitle Setup (Step 2) In this next step Welcome 2nd Step: A/V Output Settings menu you can choose your preferred audio language and TV screen settings. -
Page 13: Programme Search (Step 6)
5.0 QUICK GUIDE TO USING YOUR RECEIVER We at STRONG understand that you can’t wait to enjoy your new HD receiver. We do, however, advice you to read the full manual to get the best performance from your STRONG HD receiver. -
Page 14: Info Banner
3. Via the CH+/CH- or P-/P+ keys. 6.1.1 Direct access To gain direct access to a certain channel, simply enter its number with the 0~9 buttons on the remote control. Channel numbers can be up to four digits long. Entering a number with less than four digits is possible. -
Page 15: Subtitles
6.5 Subtitles Some channels support a choice of different subtitle languages. Press the SUB button in viewing mode to display a list of available subtitle languages. If you have switched in menu Language the Subtitle Language to a language selection, you will see these subtitles. -
Page 16: Timeshift
USB 2.0 HDD is connected to the receiver. Distorted picture and/or audio during Timeshift indicates a too low USB device speed. In the case of Timeshift being activated at channels with a high data rate (HD), STRONG cannot guarantee an accurate playback of the Timeshift file. -
Page 17: Main Menu
screen banner. Here you can select options to step, to rewind or jump forward and to read details of event and time. WARNING: For encrypted channels broadcasting rights may be limited by the provider, which is why some channels are restricted during playback to fast forward/ rewind, or possibly limited in another way. - Page 18 DiSEqC 1.1 Select a port 1 to 16 according to the connected satellite dish. Press OK to open the list of available transponders for the chosen satellite, in Transponder order to check your reception or align the antenna. Press the RED button to start scanning on the selected transponder if selection is on Transponder. Press the RED button to start scanning on the whole satellite if selection is on Satellite.
- Page 19 7.1.4 Channel Search Use this menu to perform an automatic, network or transponder channel search or to search on all satellites that have been setup. Use pq to highlight an item and t u to change settings. Below are the settings listed you can find in the search method selection.
-
Page 20: Channels And Timer Manager
7.1.6 FST/FNT Search The submenu allows you to search again manually for the broadcaster’s (FST) channel list. This option you can use to search when new channels are broadcasting but not installed yet. Simply select this option and press OK to start. 7.2 Channels and Timer Manager Select a menu item you’d like to manage TV Manager, Radio Manager,Delete all and Timer Manager. - Page 21 7.2.1.4 Delete channels Delete a channel or channels permanently from the main channel list (until you make a new search). Select the option Delete and press u. Use pq to select the channel you wish to delete. When the highlight is on that channel, press OK. In the middle section you will find the selection to delete from the channel list.
-
Page 22: Settings
7.3 Settings Use the Settings menu to configure settings for background functions, audio, video, look and feel of your receiver. Choose a setting with pq and press OK to list the possibilities or use t u to change the value of the highlighted setting. - Page 23 Select On if you would like to share basic remote control functions like Standby and Volume over the HDMI CEC control. These remote commands are send over the HDMI cable to the connected device. 7.3.3 Lock This menu enables you to define and edit your PIN code, set Installation or Menu Lock. Choose a setting with pq and press OK to list the possibilities or use t u to change the value of the highlighted setting.
-
Page 24: Storage
7.3.6 Language In this submenu you can setup the language used in the menus, preferred audio and subtitles. Change the language for the On-Screen-Display, use t u to select your Language: preferred language. It affects the menu language of your receiver so all menus and messages will be displayed in the chosen language. - Page 25 Green Step: Press the Green button Step to open the Jump By Time menu. You can select a time where you’d like to jump to. INFO Hide: Press the INFO button Hide to remove or call the timeline information banner. Media: GREEN Jump: Press the Green button Jump to open the Jump By Time menu.
-
Page 26: Tools
Formatting will permanently delete ALL data stored on the connected device. Please make a backup copy of all data you wish to keep before entering the Format menu. STRONG cannot be held responsible for loss of data from USB devices used with this receiver. - Page 27 7.5.3.1 Smartcard Status Your receiver is equipped with a smartcard slot which allows to access Irdeto encrypted services. Depending on your smartcard, you can read different information which might also be consulted from your broadcaster in order to give the most effective support. The programmes that can be descrambled are determined by the smartcard, respectively the subscription which you use.
-
Page 28: Software Update
This function allows you to perform a software update with a USB storage device. Download the software and update instructions from our website www.strong.tv and unzip it on your PC. Then load the file to the root directory of your correctly formatted USB storage device and connect it to your receiver. -
Page 29: A.1 Troubleshooting
If the receiver does not work properly after checking it, please contact your local service line or STRONG dealer. Alternatively, you can send a support mail via our website: www.strong.tv. NEVER open or disassemble your receiver. This may cause a dangerous situation and will void the warranty. - Page 30 Symptom Cause Remedy Message “No signal”. The receiver can’t receive the The weather is very bad and the satellite signal. signals are temporary blocked. The satellite dish is misaligned or distorted. Check the antenna cable, replace the cable, or connect the cable tightly to the receiver. Check in the menu if you have both good signal and quality levels.
-
Page 31: A.2 Specifications
Main processor: MSD 5029 Multimedia Audio playback: MP3* Picture view: JPG, JPEG, BMP* * STRONG cannot guarantee the playback of all files although extensions are listed, as it depends on file size, codec, bit rate and resolution Connectors SAT IN HDMI... - Page 32 TV SCART Digital audio S/PDIF coaxial USB port 2.0, type A5 V/1 A (max.) DC main power (12 V/1.5 A) General Data Power supply: 100 - 240 V AC 50/60 Hz Input voltage: 12 V DC, 1.5 A Power consumption: max.18 W, typ.