Advertisement
Transporting the Seeder
1. Check and follow all federal, state, and local
requirements before transporting the Seeder.
2. The Seeder should be transported only by tractor
required for field operation. The machine weight
should not exceed more than 1.5 times the tractor
weight. Maximum transport speed for the Seeder is
20 mph.
Excessive speed may result in loss of control of
the tractor and machine, reduced braking ability,
or failure of the machine tire or structure. Do not
exceed the machines maximum specified ground
speed regardless of the capability of the
maximum tractor speed.
3. When towing equipment in combination, the
maximum equipment ground speed shall be limited
to the lowest specified ground speed of any of the
towed machines.
Maximum transport speed shall be the lesser of
travel speed specified in the operator's manual,
speed identification symbol, information sign of
towed equipment, or limit of road conditions.
4. Slow down when driving on rough roads. Reduce speed
when turning, or on curves and slopes to avoid tipping.
Equipment altered other than the place of manufacture
may reduce the maximum transport speed. Additional
weight, added tanks, harrowing attachments, etc. may
reduce machine load carrying capabilities.
5. A Safety Chain is provided with the implement to
insure safe transport.
• The Safety Chain should have a tensile strength
equal to or greater than the gross weight of the
implement. The chain is attached to the lower Hitch
Clevis hole with two Flat Washers between the
Clamp Plates to assure a tight connection. Always
use a 1" diameter Grade 8 bolt for this connection.
• Attach the Safety Chain to the tractor drawbar.
See Figure 1-2. Provide only enough slack in the
chain for turning. Do not use an intermediate chain
support as the attaching point for the chain on the
tractor. Do not pull the implement by the safety
chain
• When unhitching from the tractor attach the hook
end of the chain to a free link close to the hitch
clevis for storage. This will keep the hook off the
ground, reducing corrosion, and keep the hook
functioning properly.
• Regularly inspect the safety chain for worn,
stretched, or broken links and ends. Replace the
safety chain if it is damaged or deformed in any way.
9K998-0522
CAUTION
6. Before transporting:
• Know the height and width of the implement being
towed. Markers, tanks, attachments, etc. can
increase the height and width of the implement.
Stay away from power lines when transporting,
extending implement. Electrocution can occur
without direct contact.
• Check to see that the tractor hitch capacity is rated
to carry the weight of the Seeder Hitch. Refer to
Tractor Operator's Manual.
• Use provided pins that properly fits the Lift Arms or
Quick Hitch and Implement Hitch.
• Clean all Hydraulic Couplings and attach to tractor
remotes.
• Connect Basic Clutch Switch Box or Brillion Elite
Mini Monitor System to tractor.
• Connect the Safety Warning Lights 7-Pin Plug into
tractor 7-Pin outlet, routing cord by avoiding pinch
points.
• Fully raise the Seeder Hydraulic Lift or 3-PT Hitch.
• Make sure Transport Locks are installed and
secured with Clevis Pins and Hair Pin Cotters.
(See "Safety Chain" on Page 3-5.)
Failure to use transport lock during transport
may result in permanent equipment damage,
serious injury, or death.
• Check all tires for proper inflation, and that lug nuts
are properly torque. (See "Tires" on Page 4-3.)
• Verify that all warnings lights, SMV sign, reflectors,
and safety decals are clearly visible and
functioning properly.
• Transport during daylight hours whenever
possible. Always use flashing warning lights,
except where such use is prohibited by law. Make
sure lights, reflectors and SMV emblem are clearly
visible and operating. Remove any obstructions
such as dirt, mud, stalks or residue that restricts
view before transporting. See Figure 3-20.
Figure 3-20: SMV Sign
OPERATION
DANGER
WARNING
3-21
Advertisement
