Related Manuals for Landoll Brillion BH1020
Summary of Contents for Landoll Brillion BH1020
- Page 1 Bridge Hitch Model BH1020 Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-778-R0...
-
Page 3: Table Of Contents
Table of Contents Introduction and Safety Information Introduction ..............1-1 Description of Unit . -
Page 5: Introduction And Safety Information
Failure to comply with this warning can result in within 10 days of retail purchase, using the Landoll to the personal injury or death, damage Corporation Ag Products on-line registration process. -
Page 6: Safety
INTRODUCTION AND SAFETY INFORMATION Figure 1-1: ID Plate Safety NOTE NOTE You should read and understand the information Investigation has shown that nearly 1/3 of all farm contained in this manual and on the implement decals accidents are caused by careless use of machinery. before you attempt to operate or maintain this equipment. -
Page 7: Transporting Safety
INTRODUCTION AND SAFETY INFORMATION • Make sure all moving parts have stopped. DANGER • Understand the procedure before doing the work. Use proper tools and equipment. • Do not allow anyone to ride on the tractor or implement. Riders could be struck by foreign Protective Equipment objects or thrown from the implement. -
Page 8: Safety Chain
INTRODUCTION AND SAFETY INFORMATION Safety Chain A second chain should be used between each Use the safety chain to help control drawn machinery implement. should it separate from the tractor drawbar. Attach the chain to the tractor drawbar support or Use a chain with a strength rating equal to or greater than specified anchor location. -
Page 9: Decals
INTRODUCTION AND SAFETY INFORMATION Decals Figure 1-3: Decals... - Page 10 INTRODUCTION AND SAFETY INFORMATION Figure 1-4: Decal Locations F-778...
-
Page 11: Assembly
Chapter 2 Assembly This chapter covers proper assembly of your implement. Refer to the BH1020 Bridge Hitch Parts Manual F-777 for complete part breakdowns and proper location of any parts not shown in the following illustrations. NOTE Additional parts identification and location can be obtained by reviewing the F-777 Parts Manual. -
Page 12: Gooseneck Coupler Installation
ASSEMBLY Gooseneck Coupler Installation Attach the Safety Chain to the Bridge Hitch by sliding three 1 inch Washers into the slotted end of the chain, At the front of the Bridge Hitch slide the Gooseneck place two 1 inch Washers between the chain and the Coupler up into the Gooseneck tube, align the top hole Bridge Hitch. -
Page 13: Bridge Hitch Installation
ASSEMBLY Bridge Hitch Installation PFT Series Bring the rear of the Bridge Hitch into position between the frame hitch plates at the center of the frame. Place two 1-1/4 Washers on each side between the Bridge Hitch and the Hitch Plates. Line up the holes and insert 1-1/4-7 x 10-1/2 Bolt, secure with Locknut. -
Page 14: Pft Series Brace Installation
ASSEMBLY PFT Series Brace Installation Rotate the Left and Right hand Hitch Braces so they are against the Upper Bridge Hitch Tube, with two holes Attach the LH Hitch Brace to the outside of the Frame above and two holes below. Insert on both sides a 1/2-13 Brace Lug and a Bridge Hitch Brace to the inside of the x 1-1/2 Bolt into the Hitch Brace and into the Bridge Hitch... -
Page 15: Pt Series Brace Installation
ASSEMBLY PT Series Brace Installation Rotate the braces so they are against the Lower Bridge Hitch Tube, with two holes above and two holes below. Attach the LH Hitch Brace to the outside of the Frame Insert 1/2-13 x 8 Bolts through the holes and secure with Brace Lug and a Bridge Hitch Brace to the inside of the Locknuts. - Page 16 ASSEMBLY PFT Series Hydraulic Cylinder this connection. Use the cylinder pins packaged with the cylinder to attach the cylinder to the machine. Be sure to Installation bend the cotter pins so that the cylinder mounting pins Attach the base end of the Pulverizer Hydraulic Cylinder to cannot disengage.
- Page 17 ASSEMBLY PT Series Hydraulic Cylinder Attach the base end of the Pulverizer Hydraulic Cylinder to the installed Extension Lug and the rod end of the Installation Hydraulic Cylinder to the Pulverizer lug. It may be Install the Lug Extension onto the Bridge Hitch Lug, by necessary to extend the cylinder rod or raise the frame aligning the Extension Lug Clevis with the Bridge Hitch slightly to make this connection.
-
Page 18: Pft Series Hydraulic Circuit Installation
ASSEMBLY PFT Series Hydraulic Circuit PFT Series You can find the components needed to assemble the Installation Hydraulic Circuit in either the Bridge Hitch Box Assembly or the Pulverizer General Box Assembly. WARNING Remove Fitting Caps prior to installing Fittings. Escaping fluid under pressure can be nearly invisible and have enough force to penetrate the skin causing serious injury. - Page 19 ASSEMBLY Figure 2-8: PFT Series Bridge Hitch Hydraulics...
-
Page 20: Series Hydraulic Circuit Installation
ASSEMBLY PT Series Hydraulic Circuit PT Series You can find the components needed to assemble the Installation Hydraulic Circuit in either the Bridge Hitch Box Assembly or the Pulverizer General Box Assembly. WARNING Remove Fitting Caps prior to installing Fittings. Escaping fluid under pressure can be nearly invisible and have enough force to penetrate the Screw a 90 degree Male ORB X Male JIC into the rod... - Page 21 ASSEMBLY Figure 2-9: PT Series Bridge Hitch Hydraulics 2-11...
- Page 22 ASSEMBLY Table provided for general use. NOTES: 2-12 F-778...
-
Page 23: Operation
This chapter will cover the basic operation and Maximum road speed is 20 MPH under good procedures for the Landoll Brillion Bridge Hitch. Be sure conditions. Do not tow the machine at a speed to read and understand the Safety Procedures and which makes vehicle control difficult. -
Page 24: Hitching The Bh1020 Bridge Hitch
OPERATION Hitching the BH1020 Bridge Hitch The BH1020 is designed to closely link a pulverizer with another implement. Proper hitching to the towing implement requires a hitch built to safely tow the Bridge Hitch on the road and in the field. A 2-5/16 Hitch Ball is required. -
Page 25: Maintenance
Chapter 4 Maintenance General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used. -
Page 26: Hydraulic Fitting Torque Specifications
MAINTENANCE Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, &ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used. -
Page 27: Fasteners
MAINTENANCE Fasteners Before operating your Brillion machine, check all hardware for tightness. (See “General Torque Specifications” on page 4-1.) After a few hours of use, check entire machine and tighten any loose nuts or bolts. Daily or periodic checks should be made thereafter. When replacing bolts, be sure to use fasteners of equal grade. - Page 28 MAINTENANCE Table provided for general use. NOTES: F-778...
-
Page 29: General Reference And Specifications
Chapter 5 General Reference and Specifications Table 5-1: Specifications Standard Machine Specifications Parking Stands Safety Chain Powder Coat Paint, Red Approximate Set-up Time: 3 Hours... - Page 30 GENERAL REFERENCE AND SPECIFICATIONS Table provided for general use. NOTES: F-778...
- Page 31 Document Control Revision Log: Date Revision Improvement(s) Description and Comments Team Member 01/2015 Initial Release...
- Page 32 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities. Bridge Hitch Model BH1020 Operator’s Manual Re-Order Part Number F-778R0 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM Copyright 2014.