ABB PVS-100-TL-B-SY2 Product Manual page 164

- Error code
- Error message Name of Alarm and Cause
- LED status
Low "Bulk" voltage (DC-DC circuit):
The alarm can be caused by causes external to
- E010 the inverter: a reduced input voltage on the inverter
- Bulk UV (just above the activation voltage) but which is not
- Yellow LED accompanied by a sufficient availability of power from
the photovoltaic generator (typical condition of the
stages with limited irradiation)
- E011 Long wait for "Booster" regime to start:
- Ramp Fault
Error internal to inverter relating to start up time for
- Yellow LED DC-DC circuit regime (Booster)
Error in the "Booster" circuit (DC-DC side)
- E012
recorded by the "Inverter" circuit (DC-AC side):
- Internal error
Error inside the inverter regarding the operation of the
- Yellow LED
DC-DC circuit part (Booster).
Excessive temperature inside the inverter:
External temperature over 60°C. This parameter also
- E014
depends on the power which the inverter must supply
- Over temperature
since the measurement of temperatures is done
- Yellow LED
internally and is influenced by the heat dissipated by
the components of the inverter itself
- E015 Breakdown recorded on the "Bulk" capacitor:
- Cap. Fault Error inside the inverter regarding a problem in the
- Yellow LED bulk capacitors.
Error in the "Inverter" circuit (DC-AC side)
- E016
recorded by the "Booster" circuit (DC-DC side):
- Internal error
The alarm is generated when a problem is detected in
- Yellow LED
the inverter circuit part (DC/AC).
Long wait for "Inverter" regime to start up:
Error internal to inverter relating to start-up time for the
DC-AC circuit regime (Inverter)
- E017 The alarm can be caused by causes external to
- Internal error the inverter: a reduced input voltage on the inverter
- Yellow LED (just above the activation voltage) but which is not
accompanied by a sufficient availability of power from
the photovoltaic generator (typical condition of the
stages with limited irradiation)
High leakage current measured on the DC side
(photovoltaic generator):
The alarm is generated when, during normal operation
- E018
of the inverter, a leakage current to ground is detected
- Leak fault in the DC section of the system. It is also possible
- Red LED that the inverter generates the alarm E018 message
also due to AC leakage currents connected to the
capacitive nature of the photovoltaic generator
compared to ground.
Failure of test on sensor to measure the leakage
current (DC side):
Before connecting to the grid the inverter runs a
self-test regarding the sensor for the leakage current.
- E019 The test is carried out by "forcing", in the sensor of
- Internal error
the leakage current, a current with a known value:
- Yellow LED the microprocessor compares the value read with the
known value.
The error is generated if the comparison between the
read value and the known value during the test does
not fall within the allowed tolerance.
Solution
- If the error signal occurs sporadically, it may be due to
causes external to the inverter (limited irradiation and so
limited power availability from the PV generator).
- If the problem occurs systematically even in conditions of
high irradiation and with input voltage which is significantly
higher than the activation voltage, contact customer
assistance.
• Error inside the inverter and cannot be checked externally.
- If the problem persists (once the inverter has been switched
off and back on again), contact customer assistance.
• Error inside the inverter and cannot be checked externally.
- If the problem persists (once the inverter has been switched
off and back on again), contact customer assistance.
• Check that the inverter is not exposed to direct sunlight. Wait
for the temperatures to which the inverter is exposed to return
to the operating range and for the inverter to cool down.
- If the problem persists (once the ambient temperature has
returned to within the range), contact customer assistance.
You must remember to wait for the time necessary to allow the
inverter to cool down.
• Error inside the inverter and cannot be checked externally.
- If the problem persists (once the inverter has been switched
off and back on again), contact customer assistance.
• Error inside the inverter and cannot be checked externally.
- If the problem persists (once the inverter has been switched
off and back on again), contact customer assistance.
- If the error signal occurs sporadically, it may be due to
causes external to the inverter (limited irradiation and so
limited power availability from the PV generator).
- If the problem occurs systematically even in conditions of
high irradiation and with input voltage which is significantly
higher than the activation voltage, contact customer
assistance.
• Measure the isolation resistance using a megohmmeter
positioned in the photovoltaic array (positive terminal short-
circuited at the negative pole) compared to ground. The
measurement is strongly influenced by the environmental
conditions, so must be made under the same conditions in
which the error occurred.
- If the value measured is lower than 1 megaohm, a
check must be carried out by a technician/installer on the
photovoltaic generator to identify and eliminate the problem.
- If the value measured is higher than 1 megaohm and the
error signal persists, contact customer assistance.
• Error inside the inverter and cannot be checked externally.
By its nature, the alarm only occurs prior to connection to the
grid
- If the problem persists (once the inverter has been switched
off and back on again), contact customer assistance.
- 164 -
8 - Maintenance