Setting Dme Wipe Modifiers - Sony XKS-C9111 User Manual

When Frame I/O (for two channels) is selected
(pattern numbers 2851 to 2854)
No. Parameter Adjustment
5 Delay Timing for video selected on a utility
bus to appear on the screen
When Frame I/O (for two channels) is selected
(pattern numbers 2861 to 2864)
No. Parameter Adjustment
1 Rot X Rotation on the Y axis (horizontal
direction)
2 Rot Y Rotation about the X axis (vertical
direction)
3 Rot Z Rotation about the Z axis
5 Delay Timing for video selected on a utility
bus to appear on the screen
When Brick (for three channels) is selected
(pattern number 3601)
Parameter group [1/2]
No. Parameter Adjustment
1 Side V Size X Side V horizontal scaling factor
2 Side V Size Y Side V vertical scaling factor
3 Height Height of brick
4 Side V Side V horizontal center position
Center X
5 Side V Side V vertical center position
Center Y
a) Common with the [Height] parameter in group 2.
b) The horizontal center position of the video pasted on Side V. At –100.00,
the center is at the left edge of the screen. At +100.00, the center is at the
right edge of the screen.
c) The vertical center position of the video pasted on Side V. At –100.00, the
center is at the bottom edge of the screen. At +100.00, the center is at the
top edge of the screen.
Parameter group [2/2]
No. Parameter Adjustment
1 Side H Size X Side H horizontal scaling factor
2 Side H Size Y Side H vertical scaling factor
3 Height Height of brick
4 Side H Side H horizontal center position
Center X
5 Side H Side H vertical center position
Center Y
a) Common with the [Height] parameter in group 1.
b) The horizontal center position of the video pasted on Side H. At –100.00,
the center is at the left edge of the screen. At +100.00, the center is at the
right edge of the screen.
c) The vertical center position of the video pasted on Side H. At –100.00, the
center is at the bottom edge of the screen. At +100.00, the center is at the
top edge of the screen.
a)
b)
c)
a)
b)
c)
161
Setting the background image
When the switcher signal format is 3840×2160P 2SI, you
can set a color signal to use as the background of DME
wipes.
Note
When the signal format is other than 3840×2160P 2SI, the
image selected on the utility 2 bus is used.
1
In the M/E-1 >DME Wipe >Edge/Direction menu
(1164), press [DME Bkgd Matte Adjust].
The Matte Adjust menu (1154.1) appears.
2
In the <Edge Matte> group, select one of the
following.
Flat Color: Use a single color signal. Set the
following parameters.
No. Parameter
1 Luminance
2 Saturation
3 Hue
Mix Color: Use a mix color signal.
For details about color mix settings, see "Carrying out
a color mix for the edge fill matte" (page 145).
Note
The color signal for the background image of DME
wipes is shared with the color matte settings for wipe
edge fills.

Setting DME Wipe Modifiers

You can apply various modifiers, such as setting the wipe
direction or the pattern position.
For an overview of modifiers and supported pattern
numbers, see "DME Wipe Pattern Variation and
Modifiers" (page 158).
Specifying the DME wipe direction
(Direction)
You can specify the DME wipe direction (normal/reverse).
To specify the wipe direction in the menu
1
Open the M/E-1 >DME Wipe >Edge/Direction menu
(1164).
Adjustment
Luminance
Saturation
Hue