Sony XKS-C9111 User Manual page 451

Enabling/disabling an input format
converter
When an XKS-S8111 is installed in the XVS-8000/7000/
6000, you can enable/disable the format converter function
for each input connector board.
Notes
• For the XKS-S8112/XKS-S9112/XKS-C8111/
XKS-C9111/XKS-C9121, setup is not required.
• When the switcher signal format is 3840×2160PsF or
1080PsF, the format converter function is not available.
• When the switcher signal format is 1080P, the format
converter function is enabled. The signal formats that
can be converted vary depending on the 720P converter
setting.
1
In the Engineering Setup >Switcher >Input menu
(7332), press [Input FC/CCR].
The Input FC/CCR menu (7332.1) appears.
2
Press [FC Format].
The FC Format menu (7332.7) appears.
3
Select the target input connector board to set.
No. Parameter Adjustment
1 Group No Input group number
a) Inputs on an input connector board form a group.
4
In the <Format Converter> group, select one of the
following.
Enable: Enable the format converter function.
Disable: Disable the format converter function.
To clear the setting
Press [Clear].
5
Press [Execute].
6
Check the message, then press [Yes].
Note
It may take a few minutes until the configuration is
completed.
Enabling/disabling the 720P converter
On an XKS-S8111, when the switcher signal format is
1080P, you can enable/disable the 720P converter. The
following conversion formats can be selected depending
on the 720P converter setting.
• When the 720P converter is disabled: 1080P (Level A),
1080P (Level B), 1080i
• When the 720P converter is enabled: 1080P (Level A),
720P
Note
For the XKS-S8112/XKS-S9112/XKS-C8111/
XKS-C9111/XKS-C9121, setup is not required.
1
In the Engineering Setup >Switcher >Input >Input FC/
CCR menu (7332.1), press [FC Format].
The FC Format menu (7332.7) appears.
2
Select the target input connector board to set.
No.
1
a) Inputs on an input connector board form a group.
3
Press [720P Converter] to enable/disable the 720P
converter.
To enable, press [720P Converter], turning it on. To
disable, press [720P Converter], turning it off.
To clear the setting
Press [Clear].
4
Press [Execute].
a)
5
Check the message, then press [Yes].
Note
It may take a few minutes until the configuration is
completed.
Setting the conversion format
You can set the signal format of inputs to convert by the
format converter.
The conversion format is set in the following groupings,
depending on the switcher signal format.
• XKS-S8111
- 3840×2160P, 1080P: Groups of 4 inputs
- 1080i, 720P: Groups of 8 inputs
• XKS-S8112
- 3840×2160P, 1080P, 1080i, 720P: Groups of 4 inputs
• XKS-S9112
- 3840×2160P 2SI or 3840×2160P SQD, and the
conversion format is 3840×2160P 2SI 12G, 1080P,
1080i: Groups of 2 inputs
- 3840×2160P 2SI or 3840×2160P SQD, and the
conversion format is 3840×2160P 2SI 3G,
3840×2160P SQD: Groups of 4 inputs
- 1080P, 1080i, 720P: Groups of 4 inputs
451
Parameter Adjustment
Group No Input group number
1)
a)